* mt7615: try wext and cfg80211
* iwinfo: support ra frequency offset
* iwinfo: ra support assolist, support AC bandwidth, read device id from mtd
* mt7615: clean code
* k2p: wireless interface should not add to bridge, wifi system will handle this
* mt7615: adapt for modern luci
* mt7615: fix Makefile, conflicts with luci-app-mtwifi
* mt_wifi: conflicts with mt7615d
* iwinfo: fix ra probe, scan list
* iwinfo: fix ra scan list
* mt7615: speed up wifi reload
* mt7615: fix bug
* mt7615: fix isolate
* mt7615: clean code
* mt7615: fix CE without cfg80211
* mt7615: split dbdc variant
* mt7615: revert config for non dbdc variant devices
* mt7615: move maccalc dependency to dbdc variant
* mt7615: append author info
* mt7615: move config generation to uci-defaults
[mac80211]
5b29614 mac80211: another fix for the sta connection monitor
1ed6eb1 mac80211: backport sched_set_fifo_low
cba4120 mac80211: add support for specifying a per-device scan list
e0d482f rt2x00: mt7620: differentiate based on SoC's CHIP_VER
[package]
amd64-microcode/intel-microcode/linux-firmware: update version
The original patch over rode the nf_conntrack_un/register_notifier API, which will
break other modules relying on the API. Reworked the notification APIs to play nice
with others. Also avoid to touch the code of fullcone nat.
Co-authored-by: quarkysg <hhtan72@yahoo.com>
The code is now much cleaner and works better than the old code.
Preparation for submitting it upstream (though with a different API)
Also add back MT7621 support and fix flow table coherence issues on
MT7622
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Co-authored-by: Felix Fietkau <nbd@nbd.name>
This commit add support for the yyets_le router.
Hardware Highlights:
SoC: Qualcomm IPQ4019 717 MHz
RAM: 512M NT5CC256M16ER-EK
Flash: 32M SPI NOR MX25L25635F
WIFI1: 2.4 GHz 2T2R integrated
WIFI2: 5 GHz 2T2R integrated
Ethernet: Qualcomm QCA8075 (4x LAN, 1x WAN)
USB: 1x 3.0
LEDS: power, wlan2g, wlan5g, usb
Button: Reset
Installation:
Upload the firmware on the upgrade page of the stcok, and this will
take a few minutes.
This commit also supports the addition of a 128M nand flash version,
just use the P&W R619AC's OpBoot to overwrite the original uboot.
Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
* autocore: add cpu freq & temp display for some arm devices
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Co-authored-by: AmadeusGhost <42570690+AmadeusGhost@users.noreply.github.com>
* Revert "show CPU Temperature for NanoPi R2S (#5612)"
This reverts commit 099439f051.
Co-authored-by: AmadeusGhost <42570690+AmadeusGhost@users.noreply.github.com>
Seemingly unneeded based on new upstream code so manually deleted:
platform/820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch
Manually merged:
generic-hack/251-sound_kconfig.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Co-authored-by: John Audia <graysky@archlinux.us>
* Revert "uboot-rockchip: update NanoPi R2S patches"
This reverts commit bda6f6572be630bcf9a1c8a429e40d8a53033af5.
This commit breaks the onboard ethernet on some units. Revert it for
now.
Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: enable Realtek PHY support
The NanoPi R2S features a Realtek Gigabit Ethernet PHY. Enable the
Realtek specific PHY driver to correctly configure internal delays.
Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-rockchip: fix nanopi-r2s failed to boot on some sd cards
Add regulator-boot-on parameters to vcc_sd.
Add startup-delay-us parameters to vcc_sdio.
This will improve the problem that in some SD cards are failing to boot up.
Signed-off-by: Yuan Tao <ty@wevs.org>
* rockchip: fix NanoPi R2S GMAC clock name
This commit fixes the name for the GMAC clock to gmac_clkin, as this is
the name of the clock provided by the rk3328-clk driver.
Without this commit, the GMAC will not work in TX direction.
Suggested-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Yuan Tao <ty@wevs.org>
* treewide: remove support for 'DEVICE_COMPAT' variable
This commit removes support for the DEVICE_COMPAT variable due to it
requires relatively few changes.
* Revert "ramips: disable PORT 5 MAC RX/TX flow control by default"
The TX/RX flow control is not the cause of the TX timeouts issue
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: net/mediatek fix logical error
fe_empty_txd() should return `tx_ring_size - 1` on ring empty, and
return 0 on ring full.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: net/mediatek disable eee
This disable eee for mt7530 ports, it causes the link down/up
issue, which happens when connecting to 100Mbit switch
Fixes: FS#1449
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: XiaoYu-C5: reuse ralink-eth driver
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
[mac80211]
ca5ee6e mac80211: Fix potential endless loop
2c14710 mac80211: add more AQL fixes/improvements
91fb3ce mac80211: remove an obsolete patch that is no longer doing anything useful
acf1733 mac80211: add preliminary support for enabling 802.11ax in config
d717343 mac80211: update encap offload patches to the latest version
673062f mac80211: allow bigger A-MSDU sizes in VHT, even if HT is limited
caf7277 mac80211: do not allow bigger VHT MPDUs than the hardware supports
cd36c0d mac80211: select the first available channel for 5GHz interfaces
1c6d456 mac80211: fix regression in station connection monitor optimization
4bd7689 mac80211: update sta connection monitor regression fix
[target]
Sync: at91, ath25, ath79, lantiq, mediatek, mvebu.
* rockchip: refresh NanoPi R2S patches
Update the patches for the NanoPi R2S to the v3 sent (and accepted)
upstream.
Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: rk3328: add compatible to NanoPi R2S ethernet PHY
This adds the compatible property to the NanoPi R2S ethernet PHY node.
Otherwise, the PHY might not be probed, as the PHY ID reads all 0xff
when it is still in reset.
Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-rockchip: update NanoPi R2S patches
Update the patches required for the NanoPi R2S to match the DTS accepted
for upstream Linux. The U-Boot patch meanwhile is still pending
upstream.
Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: refresh target patches
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Co-authored-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Co-authored-by: wevsty <ty@wevs.org>
* rockchip: fix NanoPi R2S PHY ID
Fix the PHY ID for the NanoPi R2S PHY compatible to match the used PHY.
The ID was wrong as I've accidentally picked the wrong upstream patch.
Signed-off-by: David Bauer <mail@david-bauer.net>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: wevsty <ty@wevs.org>
kernel: bump to 4.14.193, 4.19.138, 5.4.59 (#5350)
431fb8c mac80211: add AQL improvements
6bdd4c9 mac80211: add missing backports for building with 4.14 kernels
0106820 mac80211: add missing return code checks in AQL improvements
e7f7101 mac80211: rework encapsulation offload support
[package]
base-files: add function for generating random MAC
dnsmasq: abort dhcp_check on interface state
boot: sync upstream source code
ath10k-ct-firmware/mt76/sch_cake: update to latest git HEAD
[script]
download: add China Mirror Station
[target]
Sync: arc770, ath79, bcm63xx, kirkwood, lantiq, layerscape,
mediatek, mvebu, octeon, oxnas, pistachio, uml
Sync most of the target patches.
Run-compiled-on: ipq40xx (4.19 & 5.4), ramips
* mac80211: bump to 5.8-rc2
changelog:
dfe0bc8 mac80211: allow ACS restriction with fixed channel
727685c mac80211: rt2x00: define RF5592 in init_eeprom routine
cfd2f3b mac80211: create channel list for fixed channel operation
d1100c7 mac80211: Update to version 5.7.5-1
ed2015c mac80211: Update to version 5.8-rc2-1
a956c14 mac80211: util: don't warn on missing sband iftype data
8b3e170 hostapd: fix incorrect service name
68bf5a9 mac80211: don't kill wireless daemon on teardown
25e0ae6 mac80211: make cfg80211 testmode support optional (and disabled by default)
b7727a8 mac80211: fix AQL issues
3d731fc mac80211: merge performance improvement patches
* mt76: update to 2020-07-22
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mac80211: allow VHT on 2.4GHz
Allow VHT rate on 2.4GHz in order to use 256-QAM
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ath10k: allow VHT on 2.4GHz
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* hostapd: add vendor_vht option
hostapd has vendor_vht option to enable VHT (256-QAM) on 2.4GHz
Add this option to hostapd.sh so users can enable it via uci
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ipq807x: Refresh kernel configuration
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq807x: Add WCSS bus
This is needed to build ath11k.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Add ath11k
This adds the Qualcomm 802.11ax wireless chipset support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Co-authored-by: Felix Fietkau <nbd@nbd.name>
Co-authored-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: mt7621.dtsi: add missing pinctrl to ethernet node
Add rgmii1_pins (1st GMAC) and mdio_pins to ethernet node
pinctrl to ensure they are set to correct mode
* ramips: kernel: ralink-eth support mt7621
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: some devices use ralink-eth driver
Also re-added mt7621 hwnat support for some devices.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: AmadeusGhost <amadeus@openjmu.xyz>
* ramips/mt7621: re-added hwnat support
Co-authored-by: LGA1150 <dqfext@gmail.com>
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
RT-AC1300UHP has 256M memory and does not need to use ath10k-ct-smallbuffers.
Signed-off-by: AmadeusGhost <42570690+AmadeusGhost@users.noreply.github.com>
* ramips: increase HiWiFi HC5962 kernel partition to 4M
Increase kernel partition because 2M is insufficient for 4.19
Because the partition changes, previous version of OpenWrt cannot upgrade to this version
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: use all reserved space for HiWiFi HC5962
Idea was from ad6c6361f9f8 ("ath79: enable all space on Netgear ar9344-based WNDR routers")
These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt"
do not contain any device-specific data and can be used for /overlay, resulting in
121M space
Users should erase those partitions with command `mtd erase <partition name>` prior to
upgrading to this version
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Co-authored-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The Owl Loader (named after the codename that Atheros gave
these devices back in the day) has been accepted upstream.
This patch removes the "misc" driver OpenWrt had and adds
the remaining differences against the version that ships
with 5.4-rc1 into a separate "120-owl-loader-compat.patch"
file that can be cut down once AR71XX is being dealt with.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* revert: ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control
revert: ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by default
This revert c8f8e59
The TX/RX flow control is not the cause of the TX timeouts issue
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: net/mediatek fix logical error
ramips: net/mediatek fix logical error
fe_empty_txd() should return `tx_ring_size - 1` on ring empty, and
return 0 on ring full.
* ramips: net/mediatek disable eee
ramips: net/mediatek disable eee
This disable eee for mt7530 ports, it causes the link down/up
issue, which happens when connecting to 100Mbit switch
Fixes: FS#1449
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add xiaomi_miwifi-r3 support
Specification:
- CPU: 580 MHz
- Flash size: 128 MiB NAND
- RAM size: 128 MiB DDR2
- Wireless No1: SoC-integrated: MT7620A 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Wireless No2: On-board chip: MT7612E 2x2 MIMO 802.11a/n/ac (5 GHz)
- Switch: MT7620 built-in 10/100 switch w/ vlan support
- USB: 2.0 x1
Flash instructions:
1. access ssh via https://wiki.openwrt.org/toh/xiaomi/mir3
2. in ssh:
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set uart_en=1
nvram commit
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-kernel1.bin kernel1
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-rootfs0.bin rootfs0
reboot
If you want to revert back to stock fw while on LEDE:
insert usb stick (FAT/FAT32) with stock fw renamed to miwifi.bin
fw_setenv flag_last_success 0
power off the device
hold the reset button and power on the device, keep holding the reset button until yellow led starts blinking.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add mt7620-nand driver for NAND flash
This add the mt7620-nand driver
and enable nand ubifs for subtarget mt7620
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
* ath79: add support for TP-Link TL-WR882N/WR885N/WR886N
This adds support for the various clones of the TL-WR885N recently
supported ("ath79: add support for TP-Link TL-WR885N v1"):
- tplink,tl-wr882n-v1
- tplink,tl-wr882n-v2
- tplink,tl-wr882n-v3
- tplink,tl-wr885n-v1
- tplink,tl-wr885n-v2
- tplink,tl-wr886n-v2
- tplink,tl-wr886n-v3
- tplink,tl-wr886n-v4
- tplink,tl-wr886n-v5
- tplink,tl-wr886n-v6
- tplink,tl-wr886n-v7
These devices are cloned in ar71xx. All models added in this patch are the same hardware CPU
WR885n V2 was tested.
Specifications:
- SOC: Qualcomm Atheros TP9343-AL3A
- CPU: 750MHz
- Flash: 2 MiB (AH1446 25Q16BS1G E5N102)
- RAM: 16 MiB (Zentel A3S28D40JTP-50)
- WLAN: Qualcomm Atheros TP9343 450Mbps
- Ethernet: Atheros AR8228/AR8229 4 port (100M)
添加TP9343芯片的路由器型号支持，TL-WR882N/WR885N/WR886N系列
* ath79: add support for MerCury MW4530R v1
重新添加水星MW4530R路由器支持
* Repair generate mw4530r firmware default is 8M
* Fix mw4530r forgot to add network settings
* ath79: add support for TP-Link TL-WR882N/WR885N/WR886N
This adds support for the various clones of the TL-WR885N recently
supported ("ath79: add support for TP-Link TL-WR885N v1"):
- tplink,tl-wr882n-v1
- tplink,tl-wr882n-v2
- tplink,tl-wr882n-v3
- tplink,tl-wr885n-v1
- tplink,tl-wr885n-v2
- tplink,tl-wr886n-v2
- tplink,tl-wr886n-v3
- tplink,tl-wr886n-v4
- tplink,tl-wr886n-v5
- tplink,tl-wr886n-v6
- tplink,tl-wr886n-v7
These devices are cloned in ar71xx. All models added in this patch are the same hardware CPU
WR885n V2 was tested.
Specifications:
- SOC: Qualcomm Atheros TP9343-AL3A
- CPU: 750MHz
- Flash: 2 MiB (AH1446 25Q16BS1G E5N102)
- RAM: 16 MiB (Zentel A3S28D40JTP-50)
- WLAN: Qualcomm Atheros TP9343 450Mbps
- Ethernet: Atheros AR8228/AR8229 4 port (100M)
添加TP9343芯片的路由器型号支持，TL-WR882N/WR885N/WR886N系列
* ath79: add support for MerCury MW4530R v1
重新添加水星MW4530R路由器支持
* Repair generate mw4530r firmware default is 8M
From LGA1150 dalao (https://github.com/LGA1150/openwrt)
Warning: The compiled firmware only supports flashing under OpBoot.
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019
Specification:
SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
2 (USB, CAN) are GPIO
other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift
register
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
ipq40xx: fix build error for cm520-79f (#30)
This commit fix 94a743ea531b4c10e91c17dc17535471e95f308b
Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
CM520-79F: fix wan port (#33)
This commit fix 223124e
Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
CM520-79F: disable vlan
Co-authored-by: AmadeusGhost <42570690+AmadeusGhost@users.noreply.github.com>
* ath79: add support for TP-Link TL-WR882N/WR885N/WR886N
This adds support for the various clones of the TL-WR885N recently
supported ("ath79: add support for TP-Link TL-WR885N v1"):
- tplink,tl-wr882n-v1
- tplink,tl-wr882n-v2
- tplink,tl-wr882n-v3
- tplink,tl-wr885n-v1
- tplink,tl-wr885n-v2
- tplink,tl-wr886n-v2
- tplink,tl-wr886n-v3
- tplink,tl-wr886n-v4
- tplink,tl-wr886n-v5
- tplink,tl-wr886n-v6
- tplink,tl-wr886n-v7
These devices are cloned in ar71xx. All models added in this patch are the same hardware CPU
WR885n V2 was tested.
Specifications:
- SOC: Qualcomm Atheros TP9343-AL3A
- CPU: 750MHz
- Flash: 2 MiB (AH1446 25Q16BS1G E5N102)
- RAM: 16 MiB (Zentel A3S28D40JTP-50)
- WLAN: Qualcomm Atheros TP9343 450Mbps
- Ethernet: Atheros AR8228/AR8229 4 port (100M)
添加TP9343芯片的路由器型号支持，TL-WR882N/WR885N/WR886N系列
* ath79: add support for MerCury MW4530R v1
重新添加水星MW4530R路由器支持
Since commit f8c55dc ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the mmc
driver fails because it doesn't have a dma mask is set.
So set the correct dma mask.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Co-authored-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
This commit sync ramips source code from openwrt master.
1. ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by default
2. ramips: allow to set switchdev by board in ramips_set_preinit_iface
3. kernel: fix typos in KernelPackage description
* generic: support mtd-mac-address-ascii
It supports formats of both 001122334455 and 00:11:22:33:44:55
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ramips: add JDCloud
Co-authored-by: Yousong Zhou <yszhou4tech@gmail.com>
This commit sync target ath79 from openwrt master, and revert some commit which will causes wireless to not work.
Use ath10k-ct-smallbuffers by default, so that small memory devices can normal work.
