This fixes the handling of some FS copper SFP modules using
the RollBall protocol and needing some extra treatment.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Import patch from MediaTek's SDK to support FM25S01B flash.
Also fixes DS35Q1GA flash support in kernel 6.1.
Fixes: c2a01cf ("mediatek: sync kernel 6.1 from upstream")
Cleanup kernel config and drop all unrelated configs. This have the side
effect of fixing the port not going up automatically due to Bridge VLAN
Filtering disabled.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Prior to commit 8a7d12d674,
cdc-ethernet USB LTE modems (e.g. Quectel EC200A) were consistently named
usb0. After 8a7d12d67, devices began renaming to eth1 due to an assumption
that local MAC addresses originate exclusively from the kernel. Some
devices provide driver-assigned local MACs, causing point-to-point
interfaces with driver-set MACs to adopt eth%d names instead of usb%d.
Restore the naming exception for point-to-point devices: interfaces
without driver MACs or with driver-provided local MACs will retain the
usb%d convention. This addresses issues reported in [1] and fixed in [2].
[1] https://lore.kernel.org/all/Z00udyMgW6XnAw6h@atmark-techno.com/
[2] https://lore.kernel.org/all/20241203130457.904325-1-asmadeus@codewreck.org/
Tested-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce EN7581 SoC support with currently rfb board supported.
This is a new 64bit SoC from Airoha that is currently almost fully
supported upstream with only the DTS missing. Setting source-only
waiting for the full upstream support to be completed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refreshed patches for qualcommb/ipq95xx by running
make target/linux/refresh after creating a .config containing:
CONFIG_TARGET_qualcommbe=y
CONFIG_TARGET_qualcommbe_ipq95xx=y
CONFIG_TARGET_qualcommbe_ipq95xx_DEVICE_qcom_rdp433=y
Signed-off-by: John Audia <therealgraysky@proton.me>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Detect the RTL8367D chip family and set the appropriate extif
Co-authored-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Uses upstream DSA switch modules (rtl8365mb, rtl8366), similar to
RTL8367C and rtl8366rb swconfig drivers.
The package dependencies exclude targets built without kernel CONFIG_OF.
It also fixes the rtl8366rb LED support.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
These recipes are generic and will be used for other subtargets, so lets
move them to the target Makefile so they can reused.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace the existing SPI NAND controller patches with the latest v14
set that is pending upstream, and include Ansuels patch that fixes it.
Bindings patch is removed as there is no point carrying it in OpenWrt.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patch to fix Qcom SNAND driver and move the SNAND patches to
backports directory as they are shared between qualcommax and qualcommbe
target.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Follow the advise of Russell King allows to greatly improve the driver
for RealTek's 1G and 2.5G Ethernet PHYs. The results are full/half
duplex as well as Gbit master/slave property being read from PHY
Specific Status Register (PHYSR), and fixes regarding link-partner
advertisement.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of forcing 2.5G PHYs into rate-adapter mode which results higher
energy consumption, lack of support for half-duplex modes and typically
worse performance when linked at speeds less than 2.5G, use SGMII mode
which allows the MAC to follow the PHY speed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
