The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
A line in platform.sh was accidentally removed when adding support
for the Bananapi BPi-R3.
Re-add it to fix sysupgrade on the MTK7986 rfba AP.
Fixes: a96382c1bb ("mediatek: add support for Bananapi BPi-R3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The GPIO used for the RST button is also used for PCIe-CLKREQ signal.
Hence it cannot be used as button signal if PCIe is also used.
Wire up WPS button to serve as KEY_RESTART in Linux and "reset" button
in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only include recovery image in SD card image generated for the
BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only include recovery image in SD card image generated for the
BananaPi BPi-R3 if building with CONFIG_TARGET_ROOTFS_INITRAMFS.
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bananapi BPi-R3 is a development router board built around the
MediaTek Filogic 830 (MT7986A) SoC.
The board can boot either from microSD, SPI-NAND, SPI-NOR or eMMC.
Only either SPI-NAND or SPI-NOR can be used at the same time, also only
either microSD or eMMC can be used. The various storage options can be
selected using small SMD switches on the board.
Specs:
* MediaTek MT7986A (Filogic 830) 4x ARM Cortex A53
* 4T4R 2.4G 802.11bgnax (MT7975N)
* 4T4R 5G 802.11anac/ax (MT7975P)
* 2 GB DDR4 RAM
* 8 GB eMMC
* 128 MB SPI-NAND flash
* 32 MB SPI-NOR flash
* on-board MT7531 GbE switch
* 2x SFP+ (1 GbE / 2.5 GbE)
* 5x GbE network port
* miniPCIe slot (only USB 2.0 connected)
* uSIM slot (connected to miniPCIe interface)
* M.2 KEY-E PCIe interface (PCIe x2)
* microSD card interface
* 26 PIN GPIO
Hardware details: https://wiki.banana-pi.org/Banana_Pi_BPI-R3
Working:
* all 4 boot methods incl. installation via U-Boot, sysupgrade, ...
* copper LAN and WAN ports
* SFP1 (connected to gmac1, eth1 in Linux)
* WiFi
* LEDs
* Buttons
* PSTORE/ramoops based dual-boot
Not Working (missing driver features):
* SFP2 (connected to MT7531 switch)
Untested:
* M.2/NGFF slot (PCIe x2)
* mPCIe slot (USB 2.0 + SIM)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Prepare uImage.FIT partition parser for Linux 5.15
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* kernel: bump 5.10 to 5.10.143
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: refresh 5.10 patches
All patches automatically rebased.
Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
Co-authored-by: John Audia <therealgraysky@proton.me>
Backport a preliminary version of Yu Zhao's multi-generational LRU, for
improved memory management. Refresh the patches while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Ensure the MAC address for all NanoPi R4S boards is assigned unique for
each board.
FriendlyElec ship two versions of the R4S: The standard as well as the
enterprise edition with only the enterprise edition including the EEPROM
chip that stores the unique MAC address.
In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S in case the EEPROM chip is not
present by generating the board MAC from the SD card CID.
[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R4S#Differences_Between_R4S_Standard_Version_.26_R4S_Enterprise_Version
Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-rockchip:fix r4se uboot sd card not bootable
this will cause uboot to fail to load the sd card at startup, and uboot can recognize emmc
* rockchip:fix r4se system loading prompt led
* add the previous one
* fix
The patch 921-mt7986-add-mmc-support.patch introduced by commit
dabcaac443 ("mediatek: add mt7986 soc support to the target") has never
been applied in a way that it would have any effect as it actually
created a file target/linux/generic/patches-5.15/... in the kernel tree
and was probably a patch intended to be applied to openwrt.git instead
of being put into kernel patches folder as a file.
As an upstream commit from vanilla Linux also adding support for MT7986
to the mtk-sd driver has already been included we can remove that old
patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patches from Linux v5.16 and v5.17 to get 2500Base-X SFP working
again with mvneta driver after the generic phylink validate backport.
Fixes: aab466f422 ("kernel: backport generic phylink validate")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch was added in 09b086eecaa545cf7f30bc7e394a32751e25db65
("kernel: add quirk for Huawei-compatible OEM SFP GE-T"). Add patch
title, description and SoB to follow OpenWrt's developer guide for
working patches to prepare it for being sent upstream. This patch
should be discussed with Russell King and merged to Linux kernel.
Co-authored-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It was reported on Turris forum [1] that HALNy HL-GSFP module does not
work as it should with kernel 5.15. Russell King prepared this patch
series, which fixes broken SFP module to work.
Compile and run tested with Turris Omnia.
[1] https://forum.turris.cz/t/hbl-turrisos-6-0-alpha2-halny-hl-gsfp-sfp-gpon-stick-problems/17547
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Backport commit from Linux 5.18 fixing phylink with DSA drivers which
do not provide mac_select_pcs yet.
Fixes: aab466f422 ("kernel: backport generic phylink validate")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport generic phylink validate series and make use of it for
mtk_eth_soc Ethernet driver as well as mt7530 DSA driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The current target code is too chaotic, the patches are
messy and disorderly, and there are still many duplicate
code. Pack it back to half a year ago.
Mux the MT7530 switch's phy0/4 to the SoC's gmac1 on devices where RGMII2
pins are available. This achieves 2 Gbps total bandwidth to the CPU using
the second RGMII.
The ports called "wan" are muxed where possible. On a minority of devices,
this is not possible. Those cases:
mt7621_ampedwireless_ally-r1900k.dts: lan3
mt7621_ubnt_edgerouter-x.dts: eth0
mt7621_gnubee_gb-pc1.dts: ethblue
mt7621_linksys_re6500.dts: lan1
mt7621_netgear_wac104.dts: lan4
mt7621_tplink_eap235-wall-v1.dts: lan0
mt7621_tplink_eap615-wall-v1.dts: lan0
mt7621_ubnt_usw-flex.dts: lan1
The "wan" port is just what the vendor designated on the board/plastic
chasis of the device. On a technical level, there is no difference between
a lan and wan port on MT7621AT, MT7621DAT and MT7621ST SoCs. Prefer
connecting to WAN via the port described above for these devices to benefit
the feature brought with this patch.
mt7621_d-team_newifi-d2.dts cannot benefit this feature, although it looks
like it should, because the rgmii2 pins are wired to unused components.
Tested on a range of devices documented on the GitHub PR.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
These devices do not use rgmii2 as gpio, therefore remove rgmii2 pin group
from state-default. Remove overwriting the ethernet node for these devices.
Move claiming the rgmii2 group from mt7621_zyxel_nwa-ax.dtsi to
mt7621_zyxel_nwa50ax.dts as it's only the latter using rgmii2 pins as gpio.
Remove duplicate ethernet overwrite from mt7621_tplink_archer-x6-v3.dtsi.
Claim rgmii2 group as gpio on mt7621_bolt_arion.dts as it uses an rgmii2
pin, 26, as gpio.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Change switch port labels to ethblack & ethblue.
Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins.
Add the external phy with ethyellow label on the GB-PC2 devicetree.
Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function.
Enable ICPlus PHY driver for IP1001 which GB-PC2 has got.
Update interface name and change netdev function.
Enable lzma compression to make up for the increased size of the kernel.
Make spi flash bindings on par with mainline Linux to fix read errors.
Tested on GB-PC2 by Petr.
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
MAC address retrieval was switched to more generic upstream (5.13) NVMEM
based solution in commit 06bb4a5018cd ("ramips: convert mtd-mac-address
to nvmem implementation") , but NVMEM subsystem wasn't enabled in the
kernel, so fix it now.
Fixes: 06bb4a5018cd ("ramips: convert mtd-mac-address to nvmem implementation")
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message]
Older MT7623 ARMv7 SoC as well as new Filogic platforms come with
inside-secure,safexcel-eip97 units. Enable them in DTS and select the
driver kernel module by default on those platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Initially this covers MT7986 only, but it will later be expanded to cover other
Filogic branded platforms by MediaTek
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It will be supported by the new filogic subtarget
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adds support for GPON SFP modules based on the Realtek RTL8672 and
RTL9601C chips, including but not limited to:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1
Signed-off-by: Vladimir Markovets <abam_a@yahoo.com>
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
Signed-off-by: John Audia <therealgraysky@proton.me>
Co-authored-by: John Audia <therealgraysky@proton.me>
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
Signed-off-by: John Audia <therealgraysky@proton.me>
Co-authored-by: John Audia <therealgraysky@proton.me>
Runtime tested on turris-omnia and glinet-b1300.
Tested-by: John Audia <therealgraysky@proton.me> [bcm2711/RPi4B, mt7622/RT3200]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Co-authored-by: Petr Štetiar <ynezz@true.cz>
All other patches automagically rebased.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Co-authored-by: Petr Štetiar <ynezz@true.cz>
Add missing scaling_available_frequencies sysfs entry for dedicated
cpufreq driver.
This sysfs entry is not standard and each cpufreq driver needs to
provide it and declare it in the cpufreq driver struct attr.
Fixes: 5dbbefcbccc0 ("ipq806x: introduce dedicated krait cpufreq")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* armvirt: copy config files from 5.10
Copy config files from 5.10.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* armvirt: refresh 5.15 config
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* armvirt: move common symbols from subtarget to target config
These new symbols are common for all subtargets and
can be moved into target config.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Co-authored-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Co-authored-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.
Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.
Suggested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Co-authored-by: Paul Spooren <mail@aparcar.org>
* armvirt: switch to Kernel 5.10
Armvirt is a development and testing platform and should therefore use
the latest OpenWrt Kernel by default.
Tested via qemu.
Acked-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
* armvirt: add 5.15 as testing kernel
Add 5.15 as testing kernel.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Co-authored-by: Paul Spooren <mail@aparcar.org>
Co-authored-by: Aleksander Jan Bajkowski <olek2@wp.pl>
According to MediaTek MT7688 Datasheet v1.4, as well as the MT7628
counterpart, the memory controller reset bit (MC_RST) is 10, not 20.
Reset bit 20 is used for for UART 2 (UART2_RST).
Please note: Due to the lack of hardware, I was not able to test this
change.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
set_port_link is required by swconfig to setup link mode.
Here we implemented set_port_link by touching MII PHY registers.
For autoneg enabled case, we set advertise registers to let
autoneg reach the target mode and then retrigger autoneg. For
non autoneg case, we set BMCR register to force PHY enter
desired mode.
This patch have been tested on both MT7620 and MT7621.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Fixes: #10275
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: move mtk flow offload patches to backport-5.15
They were accepted upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport upstream mtk_eth_soc patches
Includes MT7986 ethernet support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Co-authored-by: Felix Fietkau <nbd@nbd.name>
Kernel switching to fw_devlink=on as default broke probing some devices.
Revert it until we get a proper fix.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
moves and extends the current facilities, which have been
added some time ago for the the usbip utility, to support
more utilites that are shipped with the Linux kernel tree
to the SDK.
this allows to drop all the hand-waving and code for
failed previous attempts to mitigate the SDK build failures.
Fixes: bdaaf66e28bd ("utils/spidev_test: build package directly from Linux")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
kernel linux now have 2 different export.h include, one from
linux/export.h and one from asm-generic/export.h
While most of our target user linux/export.h, aarch64 based target use
asm-generic/export.h that is not patched with the changes of
221-module_exports.
Patch also this additional header to fix multiple
aarch64-openwrt-linux-musl-ld: warning: orphan section `__ksymtab_strings' from `arch/arm64/kernel/head.o' being placed in section `__ksymtab_strings'
warning during kernel compilation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
On the NanoPI R4S it takes an average of 3..5 seconds for the network devices
to appear in '/proc/interrupts'.
Wait up to 10 seconds to ensure that the distribution of the interrupts
really happens.
Signed-off-by: Ronny Kotzschmar <ro.ok@me.com>
Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in.
Fixes: be0639063a70 ("kernel: bump 5.4 to 5.4.203")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch was backported to kernel 5.4.200, but without the wireguard
change, because wireguard is not available in upstream kernel 5.4.
This adds the missing changes for wireguard too.
Fixes: be0639063a70 ("kernel: bump 5.4 to 5.4.203")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Flow offload dst can become invalid after the route cache is created.
dst_check() in packet path is necessary to prevent packet drop.
Signed-off-by: Ritaro Takenaka <ritarot634@gmail.com>
In Linux v5.14 an extra feature was introduced for the RTL8211F phy,
allowing to disable a clock output from the phy. Part of that patch is to
always (soft) reset the phy upon initialisation.
This phy reset is required to have a working ethernet on the TP-Link
EAP225-Outdoor v3 and EAP225 v4 after a reboot. Otherwise the ethernet
port will only function properly on cold boots.
Tested-by: Andre Klärner <kandre@ak-online.be> # EAP225-Outdoor v3
Tested-by: Sven Hauer <sven.hauer+github@uniku.de> # EAP225 v4
Signed-off-by: Sander Vanheule <sander@svanheule.net>
For a TX->TX connected external phy to transmit/receive data, the rgmii2
pin group needs to be claimed with gpio function, at least for EdgeRouter X
SFP. We already claim the pin group under the pinctrl node with gpio
function on the gpio node on mt7621_ubnt_edgerouter-x.dtsi.
However, we should claim a pin group under its consumer node. It's the
ethernet node in this case, which we already claim the rgmii2 pin group
under it on mt7621.dtsi. Therefore, set the function as gpio on the rgmii2
node for EdgeRouter X SFP and get rid of claiming the rgmii2 pin group
under the pinctrl node. With this change, we also get to remove a
definition from mt7621_ubnt_edgerouter-x.dtsi which is specific to
EdgeRouter X SFP.
This change is tested on an EdgeRouter X SFP.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Some K2P comes with the worse boards with GD25Q128 (may be A2), which
only works with 50MHz frequency and less. Reduce spi frequency so that
these routers can boot.
remove m25p,fast-read because it isn't needed for 50MHz SPI.
Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in.
Patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
* drv-net-phy-add-JLSemi-jl2xxx-driver
* drv-net-phy-add-JLSemi-jl2xxx-driver
* drv-net-phy-add-JLSemi-jl2xxx-driver
* Enable JL201 config
* Enable JL201 config
* Enable JL201 config
* change default driver
Since the mac80211 driver cannot turn on the wireless, it can only be turned off by default.
The current reworked version cause kernel panic when the value is changes and
an interface is up. Following the tcp_be_liberal impelementation,
reimplement this to permit a safe change of this value without any
panic.
This has been tested with a QSDK package where tcp_no_window_check is used.
Fixes: 92fb51bc9881 ("generic: 5.15: standardize tcp_no_window_check pending patch")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Add the missing pinctrl properties on the ethernet node.
GMAC1 will start working with this change.
Link: https://lore.kernel.org/netdev/83a35aa3-6cb8-2bc4-2ff4-64278bbcd8c8@arinc9.com/
Overwrite pinctrl-0 property without rgmii2_pins on devicetrees which use
the rgmii2 pins as GPIO (22 - 33).
Give gpio function to rgmii2 pin group on mt7621_tplink_archer-x6-v3.dtsi
which uses GPIO 28.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
[Rebase to current source code]
Signed-off-by: AmadeusGhost <amadeus@openjmu.xyz>
Flow control needs to be enabled on both sides to work.
It is already enabled on gmac0, enable it on port@6 too.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Sungbo Eo <mans0n@gorani.run>
Remove reg property from ports node to fix this warning:
Warning (unit_address_vs_reg): /ethernet@1e100000/mdio-bus/switch@1f/ports: node has a reg or ranges property, but no unit name
Another warning surfaces afterwards. Remove #address-cells and #size-cells
from switch@1f node to fix this warning:
Warning (avoid_unnecessary_addr_size): /ethernet@1e100000/mdio-bus/switch@1f: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Device tree pcie node for this SoC is using different
styles in its different properties. Hence properly
unify them to be able to write a a proper yaml schema
documentation.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505121736.6459-11-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the YAML schema 'pci-bus.yaml' the 'device_type'
property is mandatory for all pcie root ports. Hence add it.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Property 'bus-range' when values are the default are
not necessary to be defined. Hence, remove all of them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both 'memc' and 'sysc' nodes are not using 'syscon'
as a node string which is the standard one to be used.
Update both of them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505132154.8263-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'cpc' and 'mc' nodes correspond with the MIPS 'Cluster Power Controller'
and 'MIPS Common Device Memory Map' which are present in some MIPS related
boards. There is already bindings documentation for these two located in:
- Documentation/devicetree/bindings/power/mti,mips-cpc.yaml
- Documentation/devicetree/bindings/bus/mti,mips-cdmm.yaml
Hence, properly update compatible strings and align nodes with already
mainlined bindings documentation. Also, move their definition to a proper
place since both of them are not related with the palmbus at all.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211002060706.30511-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hexadecimal addresses in device tree must be defined using lower case.
There are some of them that are still in upper case. Change them all.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211017070656.12654-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nodes 'gdma' and 'hsdma' are using magic number '4' in interrupts property.
Use 'IRQ_TYPE_LEVEL_HIGH' instead to align with the rest of the nodes in
the file.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211019102915.15409-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* kernel: bump 5.4 to 5.4.194
Signed-off-by: José Hwong <josehwong@hotmail.com>
* kernel: bump 5.4 to 5.4.195
Signed-off-by: José Hwong <josehwong@hotmail.com>
This backports a patch from Linux 5.10.116 to fix a compile problem
introduced in 5.10.114.
drivers/usb/phy/phy-generic.c could not find
devm_regulator_get_exclusive().
Fixes: #9410
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.189
Signed-off-by: José Hwong <88561480+JoseCoW@users.noreply.github.com>
* kernel: bump 5.4 to 5.4.190
Signed-off-by: José Hwong <88561480+JoseCoW@users.noreply.github.com>
Use ARMv8 Crypto Extensions for AES, ghash and sha256.
This results in a 16 times speed gain in speed for aes-128-ctr, 17x in
aes-128-gcm, and 9 times in sha256.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
kirkwood build broke due to missing include needed for ETH_ALEN.
Add patch (sent upstream as well) to address that.
Refresh patches for 5.4 and 5.10.
Fixes: #9154, #9155
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
