This target adds support for the StarFive JH7100 and JH7110 SoCs,
based on 6.12, as well as a couple boards equipped with these.
Installation:
Standard SD-card installation via dd-ing the generated image to
an SD-card of at least 256Mb.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Allow the armsr target to be built with a 6.12 kernel
when CONFIG_TESTING_KERNEL is set.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compared to v6.6 the patches to add "10gbase-r", "2500base-x",
"1000base-x", and "10g-qxgmii" modes have not been ported yet. They do
not apply cleanly to the new PCS driver. As the currently supported
hardware does not use those modes, it is not possible to test them at
this time.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 6.12 testing kernel for ath79 target is ready now.
Tested on AR9344 (ath79/nand) and QCA9531 (ath79/generic).
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add kernel package for DesignWare I2C platform controller.
This controller is used on the RP1 SoC found on RPi 5 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The kernel provides two variants of the lz4 compression a normal version
and a high compression mode version. The old kmod-lib-lz4 package
contained the normal version plus one part of the lz4hc version. There
was already code which selected the kmod-lib-lz4hc package which did
not exists.
I split this into 3 packages. kmod-lib-lz4 and kmod-lib-lz4hc for the
normal the and high compression algorithm which contain the specific
code and the kmod-lib-lz4-decompress which contains the common
decompressor.
New we are also packaging lz4hc.ko
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Change the default binutils version to 2.42.
Tested-by: Jonathan Lancett <j.lancett@ntlworld.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Backport patch to fix mipsel_24kc_24kf. Patch has been merged in
binutils master and these are straight backports with minor rework.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
QCN6122 wifi in fw-memory-mode 1 has a slightly larger caldb size than
currently defined in the ath11k driver. When coldboot calibration was
disabled, the fw mem mode was changed from 2 (256MB mem profile) to 1
(512MB mem profile), which is the correct setting for devices in scope.
However, in fw mem mode, the caldb size is 0x500000 instead of the max
0x480000 defined in the driver, causing QCN6122 wifi failing to boot:
ath11k b00a040.wifi1: qmi mem size is low to load caldata
ath11k b00a040.wifi1: failed to assign qmi target memory: -22
As such, change the max caldb memory size accordingly.
This macro is used by the driver only as a max size limit to validate
the requested caldb size returned by QMI. Different ath11k wifi chips
have different caldb sizes (for ex. the size for IPQ5018 is 0x200000).
Fixes: d4adc99 ("wifi: ath11k: disable coldboot calibration for ipq5018")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Coldboot calibration does not work causes the firmware to crash during
wifi startup. So let's disable coldboot calibration until a solution is
found.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add new setting CONFIG_NET_DSA_REALTEK_RTL8366RB_LEDS which
was introduced in kernel 6.12 and allows enabling LEDs for
the Realtek RTL8366RB subdriver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add kernel module for LP5523/LP55231 LED driver.
The kmod-leds-lp5523 depends on kmod-leds-lp55xx-common.
Signed-off-by: Sergey Shlukov <ichizakurain@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patches to enable QCN9274 radios that support both 5GHz and 6GHz
bands.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
