Siflower SF19A2890 is an SoC with:
Dual-core MIPS InterAptiv at 800MHz
DDR3 controller
One Gigabit Ethernet MAC with RGMII and IPv4 HNAT engine
Built-in 2x2 11N + 2x2 11AC WiFi radio
USB 2.0 OTG
I2C/SPI/GPIO and various other peripherals
This adds support for SF19A2890 EVB with ethernet support.
EVB spec:
Memory: DDR3 128M
Ethernet: RTL8367RB 5-port gigabit switch
Flash: 16M NOR
Others: MicroUSB OTG, LED x 1, Reset button x1
The built image can be flashed using u-boot recovery.
This target is marked as source-only until support for a commercial
router board comes.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Fix a use-after-free bug in mtk_wed_setup_tc_block_cb()
which leads to kernel panic when setup multiple ap
interfaces on one band of mt798x.
Signed-off-by: Zheng Zhang <everything411@qq.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Disables Data Center Bridging support for some network drivers by
default to avoid compilation errors when CONFIG_DCB is enabled.
Signed-off-by: Til Kaiser <mail@tk154.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_FRAME_WARN value is set by config/Config-kernel.in based on the
target type dynamically since commit:
16a2051 ("kernel: Set CONFIG_FRAME_WARN depending on target").
However, CONFIG_FRAME_WARN was not set to get filtered out so it ended up
in multiple target configs during refreshes.
So, lets filter out CONFIG_FRAME_WARN as its set dynamically to prevent it
ending up in more target configs.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Remove the rlvid analysis because for the rtl8367b family chips supported
by the driver (rtl8367rb and rtl8367r-vb), rlvid is always equal to 1.
So the code for rlvid equal to 0 is completely unnecessary.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems that some Xiaomi AX3000T boards changed to using Winbond W25N01KV
SPI-NAND which is not supported in OpenWrt nor upstream kernel.
So, add a pending patch to support it as upstream supports rest of the KV
revision models.
Signed-off-by: Robert Marko <robimarko@gmail.com>
RK3528 is a cost down SoC with high CPU performance.
However, it has poor PCIe performance (same for RK3576).
Also CPU 0/1 can't get any rest due to rkbin limitation.
Some code references: https://github.com/warpme/minimyth2
The driver for MediaTek gen3 PCIe hosts de-asserts all reset
signals at the same time using a single register write operation.
Delay the de-assertion of the #PERST signal by 100ms as some PCIe
devices fail to come up otherwise.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix PSE port assignment for 3rd GMAC on MT7988 and make sure dma_addr
is always initialized to prevent potentially accessing uninitialized
stack memory in the error path.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changes:
1. Update device baud rate.
2. Modify LED and button GPIO values and names.
3. Adjust partition layout to match the stock configuration.
4. Add missing package dependencies for USB.
5. Include device UIMAGE Magic value.
6. Revise switch layout.
7. Assign different MAC addresses.
