* mt7615: try wext and cfg80211
* iwinfo: support ra frequency offset
* iwinfo: ra support assolist, support AC bandwidth, read device id from mtd
* mt7615: clean code
* k2p: wireless interface should not add to bridge, wifi system will handle this
* mt7615: adapt for modern luci
* mt7615: fix Makefile, conflicts with luci-app-mtwifi
* mt_wifi: conflicts with mt7615d
* iwinfo: fix ra probe, scan list
* iwinfo: fix ra scan list
* mt7615: speed up wifi reload
* mt7615: fix bug
* mt7615: fix isolate
* mt7615: clean code
* mt7615: fix CE without cfg80211
* mt7615: split dbdc variant
* mt7615: revert config for non dbdc variant devices
* mt7615: move maccalc dependency to dbdc variant
* mt7615: append author info
* mt7615: move config generation to uci-defaults
* ramips: mt7621.dtsi: add missing pinctrl to ethernet node
Add rgmii1_pins (1st GMAC) and mdio_pins to ethernet node
pinctrl to ensure they are set to correct mode
* ramips: kernel: ralink-eth support mt7621
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: some devices use ralink-eth driver
Also re-added mt7621 hwnat support for some devices.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: AmadeusGhost <amadeus@openjmu.xyz>
* ramips/mt7621: re-added hwnat support
Co-authored-by: LGA1150 <dqfext@gmail.com>
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: increase HiWiFi HC5962 kernel partition to 4M
Increase kernel partition because 2M is insufficient for 4.19
Because the partition changes, previous version of OpenWrt cannot upgrade to this version
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: use all reserved space for HiWiFi HC5962
Idea was from ad6c6361f9f8 ("ath79: enable all space on Netgear ar9344-based WNDR routers")
These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt"
do not contain any device-specific data and can be used for /overlay, resulting in
121M space
Users should erase those partitions with command `mtd erase <partition name>` prior to
upgrading to this version
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Co-authored-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add xiaomi_miwifi-r3 support
Specification:
- CPU: 580 MHz
- Flash size: 128 MiB NAND
- RAM size: 128 MiB DDR2
- Wireless No1: SoC-integrated: MT7620A 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Wireless No2: On-board chip: MT7612E 2x2 MIMO 802.11a/n/ac (5 GHz)
- Switch: MT7620 built-in 10/100 switch w/ vlan support
- USB: 2.0 x1
Flash instructions:
1. access ssh via https://wiki.openwrt.org/toh/xiaomi/mir3
2. in ssh:
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set uart_en=1
nvram commit
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-kernel1.bin kernel1
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-rootfs0.bin rootfs0
reboot
If you want to revert back to stock fw while on LEDE:
insert usb stick (FAT/FAT32) with stock fw renamed to miwifi.bin
fw_setenv flag_last_success 0
power off the device
hold the reset button and power on the device, keep holding the reset button until yellow led starts blinking.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add mt7620-nand driver for NAND flash
This add the mt7620-nand driver
and enable nand ubifs for subtarget mt7620
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
This commit sync ramips source code from openwrt master.
1. ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by default
2. ramips: allow to set switchdev by board in ramips_set_preinit_iface
3. kernel: fix typos in KernelPackage description
* generic: support mtd-mac-address-ascii
It supports formats of both 001122334455 and 00:11:22:33:44:55
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ramips: add JDCloud
Co-authored-by: Yousong Zhou <yszhou4tech@gmail.com>
