Some devices with MediaTek SoCs don't use the first but only the second
MAC in the chip. Especially with MT7981 which got a built-in 1GE PHY
connected to the second MAC this is quite common.
Make sure to reset and enable PSE also in those cases by skipping gaps
using 'continue' instead of aborting the loop using 'break'.
Fixes: 75081235b8 ("generic: 6.6: (re-)add support multiple PPE to mtk_eth_soc")
Reported-by: Daniel Suchy <danny@danysek.cz>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
"linux,ubi" compatible MTD device can be automatically attached early
since commit fc153aa8d94f. Therefore, there is no need to attach MTD
devices named "ubi" or "data" again.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hardware
--------
SOC: MediaTek MT7988A (4x Cortex-A73)
RAM: 4 GiB DDR4
Flash: 128 MiB Winbond SPI-NAND
MMC: 8 GiB eMMC *or* microSD (cannot be used both)
ETH: 4x 1GE (1x WAN, 3x LAN)
2x SFP+ (10G, 5G, 2.5G, 1G)
USB: on-board USB 3.2 4-port hub
1x USB 3.2 port (type A connector)
1x M.2 for 4G/5G modem
2x mPCIe for additional modems
WiFi: optional MediaTek MT7996 Wi-Fi 7 module
(using 2x PCIe gen3 x2 on the mPCIe slots and 12V power)
Installation
------------
1. Decompress and write the sdcard image to a micro SD card and use that
to boot the R4 (both dip switches in upper position).
2. Use the bootloader menu accessible via the serial console to install
to SPI-NAND.
3. Switch to boot from SPI-NAND and install to eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add 'fitblk' driver to replace the rejected/deprecated uImage.FIT
partition parser.
To use the new driver, add phandle /chosen/rootdisk and point it to
the MTD partition, UBI volume or block device holding the uImage.FIT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to allow gradually migrating the boards currently using the
uImage.FIT partition (deprecated/rejected) parser to the new fitblk
driver, skip the partition parser code in case the new fitblk driver
(which serves the same purpose) is used.
As an indicator for the use of the new fitblk driver, check if the
/chosen/rootdisk property is present in the Device Tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The partition parser approach has been rejected upstream, it will be
replaced by a small block driver which is the solution suggestion by
upstream maintainers.
As the partition parser has only been used by the mediatek target, as
a first step, move it there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that the issue with WED has been sorted out, re-add support for
multiple PPE to the mtk_eth_soc driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport patch adding support for LED PHY directly in PHY ops struct.
Add new PHYLIB_LEDS config and refresh patches.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport upstream code split patch for qca8k needed for ipq40xx target
to correctly implement a DSA driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport initial LEDs hw control support. Currently this is limited to
only rx/tx and link events for the netdev trigger but the API got
accepted and the additional modes are working on and will be backported
later.
Refresh every patch and add the additional config flag for QCA8K new
LEDs support.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Switch to OpenWrt uImage.FIT bootmethod and include various bootloader
artifacts with the generated binaries.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport commit fixing detection of SFP modules which has been broken
since Linux 6.4 for some modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
