* drv-net-phy-add-JLSemi-jl2xxx-driver
* drv-net-phy-add-JLSemi-jl2xxx-driver
* drv-net-phy-add-JLSemi-jl2xxx-driver
* Enable JL201 config
* Enable JL201 config
* Enable JL201 config
* change default driver
Since the mac80211 driver cannot turn on the wireless, it can only be turned off by default.
* Rockchip:Fix dtsi of doornet2
phy:
Modify phy timing;The manufacturer's board requires two timing modes: 125m and 25m ---stmmac_mdio.c stmmac_main.c
Among them, stmmac_main.c is added with 1.5 reset, and the compilation of other devices is not affected
emmc:
In emmc hs400 mode, the performance test effect is the same as hs200, so it is safer to reduce hs200
* Rockchip:Add doornet2 to overclock to 2.2GHz/1.8GHz
* Create 105-rockchip-rk3399-Add-support-for-EmbedFire-DoorNet2.patch
Modify the startup method: SD starts first, which is convenient for saving bricks. If there is no system in SD, it will automatically jump to the next emmc boot
* Update with kernel 5.4
* Update 992-rockchip-rk3399-overclock-to-2.2-1.8-GHz-for-NanoPi4.patch
Some boards have SD card connectors where the power rail cannot be switched
off by the driver. If the card has not been power cycled, it may still be
using 1.8V signaling after a warm re-boot. Bootroms expecting 3.3V signaling
will fail to boot from a UHS card that continue to use 1.8V signaling.
Set initial signal voltage in mmc_power_off() to allow re-boot to function.
This fixes re-boot with UHS cards on Asus Tinker Board (Rockchip RK3288),
same issue have been seen on some Rockchip RK3399 boards.
Signed-off-by: CN_SZTL <cnsztl@immortalwrt.org>
Co-authored-by: CN_SZTL <22235437+1715173329@users.noreply.github.com>
Some boards have SD card connectors where the power rail cannot be switched
off by the driver. If the card has not been power cycled, it may still be
using 1.8V signaling after a warm re-boot. Bootroms expecting 3.3V signaling
will fail to boot from a UHS card that continue to use 1.8V signaling.
Set initial signal voltage in mmc_power_off() to allow re-boot to function.
This fixes re-boot with UHS cards on Asus Tinker Board (Rockchip RK3288),
same issue have been seen on some Rockchip RK3399 boards.
Backport from https://lore.kernel.org/linux-rockchip/AM3PR03MB09664161A7FA2BD68B2800A7AC620@AM3PR03MB0966.eurprd03.prod.outlook.com/
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
* Revert "uboot-rockchip: update NanoPi R2S patches"
This reverts commit bda6f6572be630bcf9a1c8a429e40d8a53033af5.
This commit breaks the onboard ethernet on some units. Revert it for
now.
Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: enable Realtek PHY support
The NanoPi R2S features a Realtek Gigabit Ethernet PHY. Enable the
Realtek specific PHY driver to correctly configure internal delays.
Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-rockchip: fix nanopi-r2s failed to boot on some sd cards
Add regulator-boot-on parameters to vcc_sd.
Add startup-delay-us parameters to vcc_sdio.
This will improve the problem that in some SD cards are failing to boot up.
Signed-off-by: Yuan Tao <ty@wevs.org>
* rockchip: fix NanoPi R2S GMAC clock name
This commit fixes the name for the GMAC clock to gmac_clkin, as this is
the name of the clock provided by the rk3328-clk driver.
Without this commit, the GMAC will not work in TX direction.
Suggested-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Yuan Tao <ty@wevs.org>
* rockchip: refresh NanoPi R2S patches
Update the patches for the NanoPi R2S to the v3 sent (and accepted)
upstream.
Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: rk3328: add compatible to NanoPi R2S ethernet PHY
This adds the compatible property to the NanoPi R2S ethernet PHY node.
Otherwise, the PHY might not be probed, as the PHY ID reads all 0xff
when it is still in reset.
Signed-off-by: David Bauer <mail@david-bauer.net>
* uboot-rockchip: update NanoPi R2S patches
Update the patches required for the NanoPi R2S to match the DTS accepted
for upstream Linux. The U-Boot patch meanwhile is still pending
upstream.
Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: refresh target patches
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Co-authored-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Co-authored-by: wevsty <ty@wevs.org>
* rockchip: fix NanoPi R2S PHY ID
Fix the PHY ID for the NanoPi R2S PHY compatible to match the used PHY.
The ID was wrong as I've accidentally picked the wrong upstream patch.
Signed-off-by: David Bauer <mail@david-bauer.net>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: wevsty <ty@wevs.org>
kernel: bump to 4.14.193, 4.19.138, 5.4.59 (#5350)
431fb8c mac80211: add AQL improvements
6bdd4c9 mac80211: add missing backports for building with 4.14 kernels
0106820 mac80211: add missing return code checks in AQL improvements
e7f7101 mac80211: rework encapsulation offload support
[package]
base-files: add function for generating random MAC
dnsmasq: abort dhcp_check on interface state
boot: sync upstream source code
ath10k-ct-firmware/mt76/sch_cake: update to latest git HEAD
[script]
download: add China Mirror Station
[target]
Sync: arc770, ath79, bcm63xx, kirkwood, lantiq, layerscape,
mediatek, mvebu, octeon, oxnas, pistachio, uml
Sync most of the target patches.
Run-compiled-on: ipq40xx (4.19 & 5.4), ramips
