Raising the temperatures for passive and active trips. @VA1DER
proposed at issue 9396 to remove passive trip. This commit relates to
his suggestion.
Without this patch. the CPU will be throttled all the way down to 98MHz
if the temperature rises even a degree above the trip point, and it was
further discovered that if the internal temperature of the device is
above the first trip point temperature when it boots then it will start
in a throttled state and even
$ echo disabled > /sys/class/thermal/thermal_zone0/mode
will have no effect.
The patch increases the passive trip point and active cooling map. The
throttling temperature will then be at 77°C and 82°C, which is still a
low enough temperature for ARM devices to not be in the real danger
zone, and gives some operational headroom.
Signed-off-by: Bruno Umuarama <anonimou_eu@hotmail.com>
* set correct clocks for PWM to work.
* MT7986 PWM does have the 26MHz-clock-select, set that in patch
* drop useless 'passive' trip point in thermal zone
* extend pwm-fan to have 3 active operating points
* set reasonable trip points in thermal zone
* invert pwm-fan operating points and set shorter period to allow
less noisy operation of the PWM fan of the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Setup thermal zone, select pins and enabled drivers for I2C (on 26-pin
GPIO bank) and PWM (1x fan and 1x GPIO bank).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for hardware I2C and PWM units found in the Filogic SoCs
as well as the CPU thermal support.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.19 to 5.19.13
All patches automatically rebased
Signed-off-by: Liu Linhui <liulinhui36@gmail.com>
* kernel: bump 5.19 to 5.19.14
All patches automatically rebased.
Signed-off-by: Liu Linhui <liulinhui36@gmail.com>
Signed-off-by: Liu Linhui <liulinhui36@gmail.com>
Removed upstreamed:
generic/pending-5.15/722-net-mt7531-only-do-PLL-once-after-the-reset.patch
All other patches automatically rebased.
Signen-off-by: Liu Linhui <liulinhui36@gmail.com>
This fixes following compile error seen when
building mac80211 with mesh disabled:
.../backports-5.15.58-1/net/mac80211/agg-rx.c: In function 'ieee80211_send_addba_resp':
...backports-5.15.58-1/net/mac80211/agg-rx.c:255:17: error: 'struct sta_info' has no member named 'mesh'
255 | if (!sta->mesh)
| ^~
sta_info.h shows this item as being optional based on flags:
struct mesh_sta *mesh;
Guard the check to fix this.
Fixes: f96744ba6b ("mac80211: mask nested A-MSDU support for mesh")
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
mac80211 incorrectly processes A-MSDUs contained in A-MPDU frames. This
results in dropped packets and severely impacted throughput.
As a workaround, don't indicate support for A-MSDUs contained in
A-MPDUs. This improves throughput over mesh links by factor 10.
Signed-off-by: David Bauer <mail@david-bauer.net>
Import patches from mtk-openwrt-feeds (MTK SDK) to support reading
t-phy settings affecting PCIe as well as USB2 and USB3 from efuse.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
efuse is used to store board-specific settings of some of the in-SoC
peripherals. Add it to device tree, so it gets probed on boot and can
be accessed by other drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow byte-wise access to mtk-efuse as some drivers require that.
Patch imported from mtk-openwrt-feeds (MTK SDK).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
