298977887/lede
1
0
Fork 0
mirror of https://github.com/coolsnowwolf/lede.git synced 2025-08-11 19:13:43 +08:00
Code Issues Packages Projects Releases Wiki Activity
lede/package/kernel/mac80211/ralink.mk
coolsnowwolf 88beed4c56 mac80211: netifd: Use a mask when using Usage: iw [options] command 
Options:
	--debug		enable netlink debugging
	--version	show version (3.4)
Commands:
	help [command]
		Print usage for all or a specific command, e.g.
		"help wowlan" or "help wowlan enable".

	event [-t] [-r] [-f]
		Monitor events from the kernel.
		-t - print timestamp
		-r - print relative timstamp
		-f - print full frame for auth/assoc etc.

	phy
	list
		List all wireless devices and their capabilities.

	phy <phyname> info
		Show capabilities for the specified wireless device.

	dev
		List all network interfaces for wireless hardware.

	dev <devname> info
		Show information for this interface.

	dev <devname> del
		Remove this virtual interface

	dev <devname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*]
	phy <phyname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*]
		Add a new virtual interface with the given configuration.
		Valid interface types are: managed, ibss, monitor, mesh, wds.

		The flags are only used for monitor interfaces, valid flags are:
		none:     no special flags
		fcsfail:  show frames with FCS errors
		control:  show control frames
		otherbss: show frames from other BSSes
		cook:     use cooked mode

		The mesh_id is used only for mesh mode.

	dev <devname> ibss join <SSID> <freq in MHz> [HT20|HT40+|HT40-|NOHT] [fixed-freq] [<fixed bssid>] [beacon-interval <TU>] [basic-rates <rate in Mbps,rate2,...>] [mcast-rate <rate in Mbps>] [key d:0:abcde]
		Join the IBSS cell with the given SSID, if it doesn't exist create
		it on the given frequency. When fixed frequency is requested, don't
		join/create a cell on a different frequency. When a fixed BSSID is
		requested use that BSSID and do not adopt another cell's BSSID even
		if it has higher TSF and the same SSID. If an IBSS is created, create
		it with the specified basic-rates, multicast-rate and beacon-interval.

	dev <devname> ibss leave
		Leave the current IBSS cell.

	dev <devname> station dump
		List all stations known, e.g. the AP on managed interfaces

	dev <devname> station set <MAC address> vlan <ifindex>
		Set an AP VLAN for this station.

	dev <devname> station set <MAC address> plink_action <open|block>
		Set mesh peer link action for this station (peer).

	dev <devname> station del <MAC address>
		Remove the given station entry (use with caution!)

	dev <devname> station get <MAC address>
		Get information for a specific station.

	dev <devname> survey dump
		List all gathered channel survey data

	dev <devname> mesh leave
		Leave a mesh.

	dev <devname> mesh join <mesh ID> [mcast-rate <rate in Mbps>] [<param>=<value>]*
		Join a mesh with the given mesh ID with mcast-rate and mesh parameters.

	dev <devname> mpath dump
		List known mesh paths.

	dev <devname> mpath set <destination MAC address> next_hop <next hop MAC address>
		Set an existing mesh path's next hop.

	dev <devname> mpath new <destination MAC address> next_hop <next hop MAC address>
		Create a new mesh path (instead of relying on automatic discovery).

	dev <devname> mpath del <MAC address>
		Remove the mesh path to the given node.

	dev <devname> mpath get <MAC address>
		Get information on mesh path to the given node.

	dev <devname> scan [-u] [freq <freq>*] [ies <hex as 00:11:..>] [ssid <ssid>*|passive]
		Scan on the given frequencies and probe for the given SSIDs
		(or wildcard if not given) unless passive scanning is requested.
		If -u is specified print unknown data in the scan results.
		Specified (vendor) IEs must be well-formed.

	dev <devname> scan trigger [freq <freq>*] [ies <hex as 00:11:..>] [ssid <ssid>*|passive]
		Trigger a scan on the given frequencies with probing for the given
		SSIDs (or wildcard if not given) unless passive scanning is requested.

	dev <devname> scan dump [-u]
		Dump the current scan results. If -u is specified, print unknown
		data in scan results.

	reg get
		Print out the kernel's current regulatory domain information.

	reg set <ISO/IEC 3166-1 alpha2>
		Notify the kernel about the current regulatory domain.

	dev <devname> connect [-w] <SSID> [<freq in MHz>] [<bssid>] [key 0:abcde d:1:6162636465]
		Join the network with the given SSID (and frequency, BSSID).
		With -w, wait for the connect to finish or fail.

	dev <devname> disconnect
		Disconnect from the current network.

	dev <devname> link
		Print information about the current link, if any.

	dev <devname> offchannel <freq> <duration>
		Leave operating channel and go to the given channel for a while.

	dev <devname> cqm rssi <threshold|off> [<hysteresis>]
		Set connection quality monitor RSSI threshold.

	phy <phyname> wowlan show
		Show WoWLAN status.

	phy <phyname> wowlan disable
		Disable WoWLAN.

	phy <phyname> wowlan enable [any] [disconnect] [magic-packet] [gtk-rekey-failure] [eap-identity-request] [4way-handshake] [rfkill-release] [patterns <pattern>*]
		Enable WoWLAN with the given triggers.
		Each pattern is given as a bytestring with '-' in places where any byte
		may be present, e.g. 00:11:22:-:44 will match 00:11:22:33:44 and
		00:11:22:33:ff:44 etc.

	dev <devname> roc start <freq> <time>

	phy <phyname> set antenna <bitmap> | all | <tx bitmap> <rx bitmap>
		Set a bitmap of allowed antennas to use for TX and RX.
		The driver may reject antenna configurations it cannot support.

	dev <devname> set txpower <auto|fixed|limit> [<tx power in mBm>]
		Specify transmit power level and setting type.

	phy <phyname> set txpower <auto|fixed|limit> [<tx power in mBm>]
		Specify transmit power level and setting type.

	phy <phyname> set distance <distance>
		Set appropriate coverage class for given link distance in meters.
		Valid values: 0 - 114750

	phy <phyname> set coverage <coverage class>
		Set coverage class (1 for every 3 usec of air propagation time).
		Valid values: 0 - 255.

	phy <phyname> set netns <pid>
		Put this wireless device into a different network namespace

	phy <phyname> set rts <rts threshold|off>
		Set rts threshold.

	phy <phyname> set frag <fragmentation threshold|off>
		Set fragmentation threshold.

	dev <devname> set channel <channel> [HT20|HT40+|HT40-]
	phy <phyname> set channel <channel> [HT20|HT40+|HT40-]
	dev <devname> set freq <freq> [HT20|HT40+|HT40-]
	phy <phyname> set freq <freq> [HT20|HT40+|HT40-]
		Set frequency/channel the hardware is using, including HT
		configuration.

	phy <phyname> set name <new name>
		Rename this wireless device.

	dev <devname> set peer <MAC address>
		Set interface WDS peer.

	dev <devname> set noack_map <map>
		Set the NoAck map for the TIDs. (0x0009 = BE, 0x0006 = BK, 0x0030 = VI, 0x00C0 = VO)

	dev <devname> set 4addr <on|off>
		Set interface 4addr (WDS) mode.

	dev <devname> set type <type>
		Set interface type/mode.
		Valid interface types are: managed, ibss, monitor, mesh, wds.

	dev <devname> set meshid <meshid>
	dev <devname> set monitor <flag>*
		Set monitor flags. Valid flags are:
		none:     no special flags
		fcsfail:  show frames with FCS errors
		control:  show control frames
		otherbss: show frames from other BSSes
		cook:     use cooked mode

	dev <devname> set mesh_param <param>=<value> [<param>=<value>]*
		Set mesh parameter (run command without any to see available ones).

	dev <devname> set power_save <on|off>
		Set power save state to on or off.

	dev <devname> set bitrates [legacy-<2.4|5> <legacy rate in Mbps>*] [mcs-<2.4|5> <MCS index>*]
		Sets up the specified rate masks.
		Not passing any arguments would clear the existing mask (if any).

	dev <devname> get mesh_param [<param>]
		Retrieve mesh parameter (run command without any to see available ones).

	dev <devname> get power_save <param>
		Retrieve power save state.

You can omit the 'phy' or 'dev' if the identification is unique,
e.g. "iw wlan0 info" or "iw phy0 info". (Don't when scripting.)

Do NOT screenscrape this tool, we don't consider its output stable.
2019-03-20 13:58:58 +08:00

173 lines
5.8 KiB
Makefile
Raw Blame History

PKG_DRIVERS += \
rt2x00-lib rt2x00-pci rt2x00-usb rt2x00-mmio \
rt2400-pci rt2500-pci rt2500-usb \
rt2800-lib rt2800-mmio rt2800-pci rt2800-soc rt2800-usb \
rt61-pci rt73-usb
PKG_CONFIG_DEPENDS += \
CONFIG_PACKAGE_RT2X00_LIB_DEBUGFS \
CONFIG_PACKAGE_RT2X00_DEBUG
config-$(call config_package,rt2x00-lib) += RT2X00 RT2X00_LIB
config-$(call config_package,rt2x00-pci) += RT2X00_LIB_PCI
config-$(call config_package,rt2x00-mmio) += RT2X00_LIB_MMIO
config-$(call config_package,rt2x00-usb) += RT2X00_LIB_USB
config-$(CONFIG_PACKAGE_RT2X00_LIB_DEBUGFS) += RT2X00_LIB_DEBUGFS
config-$(CONFIG_PACKAGE_RT2X00_DEBUG) += RT2X00_DEBUG
config-$(call config_package,rt2400-pci) += RT2400PCI
config-$(call config_package,rt2500-pci) += RT2500PCI
config-$(call config_package,rt2500-usb) += RT2500USB
config-$(call config_package,rt61-pci) += RT61PCI
config-$(call config_package,rt73-usb) += RT73USB
config-$(call config_package,rt2800-lib) += RT2800_LIB
config-$(call config_package,rt2800-soc) += RT2800SOC
config-$(call config_package,rt2800-pci) += RT2800PCI
config-y += RT2800PCI_RT33XX RT2800PCI_RT35XX RT2800PCI_RT53XX RT2800PCI_RT3290
config-$(call config_package,rt2800-usb) += RT2800USB
config-y += RT2800USB_RT33XX RT2800USB_RT35XX RT2800USB_RT3573 RT2800USB_RT53XX RT2800USB_RT55XX RT2800USB_UNKNOWN
define KernelPackage/rt2x00/Default
$(call KernelPackage/mac80211/Default)
TITLE:=Ralink Drivers for RT2x00 cards
endef
define KernelPackage/rt2x00-lib
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @(PCI_SUPPORT||USB_SUPPORT||TARGET_ramips) +kmod-mac80211 +kmod-lib-crc-itu-t
TITLE+= (LIB)
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2x00lib.ko
MENU:=1
endef
define KernelPackage/rt2x00-lib/config
if PACKAGE_kmod-rt2x00-lib
config PACKAGE_RT2X00_LIB_DEBUGFS
bool "Enable rt2x00 debugfs support"
depends on PACKAGE_MAC80211_DEBUGFS
help
Enable creation of debugfs files for the rt2x00 drivers.
These debugfs files support both reading and writing of the
most important register types of the rt2x00 hardware.
config PACKAGE_RT2X00_DEBUG
bool "Enable rt2x00 debug output"
help
Enable debugging output for all rt2x00 modules
endif
endef
define KernelPackage/rt2x00-mmio
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @(PCI_SUPPORT||TARGET_ramips) +kmod-rt2x00-lib +kmod-eeprom-93cx6
HIDDEN:=1
TITLE+= (MMIO)
FILES:= $(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2x00mmio.ko
endef
define KernelPackage/rt2x00-pci
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @PCI_SUPPORT +kmod-rt2x00-mmio +kmod-rt2x00-lib
HIDDEN:=1
TITLE+= (PCI)
FILES:= $(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2x00pci.ko
AUTOLOAD:=$(call AutoProbe,rt2x00pci)
endef
define KernelPackage/rt2x00-usb
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @USB_SUPPORT +kmod-rt2x00-lib +kmod-usb-core
HIDDEN:=1
TITLE+= (USB)
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2x00usb.ko
AUTOLOAD:=$(call AutoProbe,rt2x00usb)
endef
define KernelPackage/rt2800-lib
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @(PCI_SUPPORT||USB_SUPPORT||TARGET_ramips) +kmod-rt2x00-lib +kmod-lib-crc-ccitt +@DRIVER_11N_SUPPORT +@DRIVER_11W_SUPPORT
HIDDEN:=1
TITLE+= (rt2800 LIB)
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2800lib.ko
endef
define KernelPackage/rt2400-pci
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @PCI_SUPPORT +kmod-rt2x00-pci
TITLE+= (RT2400 PCI)
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2400pci.ko
AUTOLOAD:=$(call AutoProbe,rt2400pci)
endef
define KernelPackage/rt2500-pci
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @PCI_SUPPORT +kmod-rt2x00-pci
TITLE+= (RT2500 PCI)
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2500pci.ko
AUTOLOAD:=$(call AutoProbe,rt2500pci)
endef
define KernelPackage/rt2500-usb
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @USB_SUPPORT +kmod-rt2x00-usb
TITLE+= (RT2500 USB)
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2500usb.ko
AUTOLOAD:=$(call AutoProbe,rt2500usb)
endef
define KernelPackage/rt2800-mmio
$(call KernelPackage/rt2x00/Default)
TITLE += (RT28xx/RT3xxx MMIO)
DEPENDS += +kmod-rt2800-lib +kmod-rt2x00-mmio
HIDDEN:=1
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2800mmio.ko
endef
define KernelPackage/rt2800-soc
$(call KernelPackage/rt2x00/Default)
DEPENDS += @(TARGET_ramips_rt288x||TARGET_ramips_rt305x||TARGET_ramips_rt3883||TARGET_ramips_mt7620) +kmod-rt2800-mmio +kmod-rt2800-lib
TITLE += (RT28xx/RT3xxx SoC)
FILES := \
$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2x00soc.ko \
$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2800soc.ko
AUTOLOAD:=$(call AutoProbe,rt2800soc)
endef
define KernelPackage/rt2800-pci
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @PCI_SUPPORT +kmod-rt2x00-pci +kmod-rt2800-lib +kmod-rt2800-mmio +rt2800-pci-firmware
TITLE+= (RT2860 PCI)
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2800pci.ko
AUTOLOAD:=$(call AutoProbe,rt2800pci)
endef
define KernelPackage/rt2800-usb
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @USB_SUPPORT +kmod-rt2x00-usb +kmod-rt2800-lib +kmod-lib-crc-ccitt +rt2800-usb-firmware
TITLE+= (RT2870 USB)
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt2800usb.ko
AUTOLOAD:=$(call AutoProbe,rt2800usb)
endef
define KernelPackage/rt61-pci
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @PCI_SUPPORT +kmod-rt2x00-pci +rt61-pci-firmware
TITLE+= (RT2x61 PCI)
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt61pci.ko
AUTOLOAD:=$(call AutoProbe,rt61pci)
endef
define KernelPackage/rt73-usb
$(call KernelPackage/rt2x00/Default)
DEPENDS+= @USB_SUPPORT +kmod-rt2x00-usb +rt73-usb-firmware
TITLE+= (RT73 USB)
FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ralink/rt2x00/rt73usb.ko
AUTOLOAD:=$(call AutoProbe,rt73usb)
endef
Reference in New Issue View Git Blame Copy Permalink