lede/package/kernel/mac80211/patches/subsys/522-mac80211_configure_antenna_gain.patch
coolsnowwolf 88beed4c56 mac80211: netifd: Use a mask when using Usage: iw [options] command
Options:
	--debug		enable netlink debugging
	--version	show version (3.4)
Commands:
	help [command]
		Print usage for all or a specific command, e.g.
		"help wowlan" or "help wowlan enable".

	event [-t] [-r] [-f]
		Monitor events from the kernel.
		-t - print timestamp
		-r - print relative timstamp
		-f - print full frame for auth/assoc etc.

	phy
	list
		List all wireless devices and their capabilities.

	phy <phyname> info
		Show capabilities for the specified wireless device.

	dev
		List all network interfaces for wireless hardware.

	dev <devname> info
		Show information for this interface.

	dev <devname> del
		Remove this virtual interface

	dev <devname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*]
	phy <phyname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*]
		Add a new virtual interface with the given configuration.
		Valid interface types are: managed, ibss, monitor, mesh, wds.

		The flags are only used for monitor interfaces, valid flags are:
		none:     no special flags
		fcsfail:  show frames with FCS errors
		control:  show control frames
		otherbss: show frames from other BSSes
		cook:     use cooked mode

		The mesh_id is used only for mesh mode.

	dev <devname> ibss join <SSID> <freq in MHz> [HT20|HT40+|HT40-|NOHT] [fixed-freq] [<fixed bssid>] [beacon-interval <TU>] [basic-rates <rate in Mbps,rate2,...>] [mcast-rate <rate in Mbps>] [key d:0:abcde]
		Join the IBSS cell with the given SSID, if it doesn't exist create
		it on the given frequency. When fixed frequency is requested, don't
		join/create a cell on a different frequency. When a fixed BSSID is
		requested use that BSSID and do not adopt another cell's BSSID even
		if it has higher TSF and the same SSID. If an IBSS is created, create
		it with the specified basic-rates, multicast-rate and beacon-interval.

	dev <devname> ibss leave
		Leave the current IBSS cell.

	dev <devname> station dump
		List all stations known, e.g. the AP on managed interfaces

	dev <devname> station set <MAC address> vlan <ifindex>
		Set an AP VLAN for this station.

	dev <devname> station set <MAC address> plink_action <open|block>
		Set mesh peer link action for this station (peer).

	dev <devname> station del <MAC address>
		Remove the given station entry (use with caution!)

	dev <devname> station get <MAC address>
		Get information for a specific station.

	dev <devname> survey dump
		List all gathered channel survey data

	dev <devname> mesh leave
		Leave a mesh.

	dev <devname> mesh join <mesh ID> [mcast-rate <rate in Mbps>] [<param>=<value>]*
		Join a mesh with the given mesh ID with mcast-rate and mesh parameters.

	dev <devname> mpath dump
		List known mesh paths.

	dev <devname> mpath set <destination MAC address> next_hop <next hop MAC address>
		Set an existing mesh path's next hop.

	dev <devname> mpath new <destination MAC address> next_hop <next hop MAC address>
		Create a new mesh path (instead of relying on automatic discovery).

	dev <devname> mpath del <MAC address>
		Remove the mesh path to the given node.

	dev <devname> mpath get <MAC address>
		Get information on mesh path to the given node.

	dev <devname> scan [-u] [freq <freq>*] [ies <hex as 00:11:..>] [ssid <ssid>*|passive]
		Scan on the given frequencies and probe for the given SSIDs
		(or wildcard if not given) unless passive scanning is requested.
		If -u is specified print unknown data in the scan results.
		Specified (vendor) IEs must be well-formed.

	dev <devname> scan trigger [freq <freq>*] [ies <hex as 00:11:..>] [ssid <ssid>*|passive]
		Trigger a scan on the given frequencies with probing for the given
		SSIDs (or wildcard if not given) unless passive scanning is requested.

	dev <devname> scan dump [-u]
		Dump the current scan results. If -u is specified, print unknown
		data in scan results.

	reg get
		Print out the kernel's current regulatory domain information.

	reg set <ISO/IEC 3166-1 alpha2>
		Notify the kernel about the current regulatory domain.

	dev <devname> connect [-w] <SSID> [<freq in MHz>] [<bssid>] [key 0:abcde d:1:6162636465]
		Join the network with the given SSID (and frequency, BSSID).
		With -w, wait for the connect to finish or fail.

	dev <devname> disconnect
		Disconnect from the current network.

	dev <devname> link
		Print information about the current link, if any.

	dev <devname> offchannel <freq> <duration>
		Leave operating channel and go to the given channel for a while.

	dev <devname> cqm rssi <threshold|off> [<hysteresis>]
		Set connection quality monitor RSSI threshold.

	phy <phyname> wowlan show
		Show WoWLAN status.

	phy <phyname> wowlan disable
		Disable WoWLAN.

	phy <phyname> wowlan enable [any] [disconnect] [magic-packet] [gtk-rekey-failure] [eap-identity-request] [4way-handshake] [rfkill-release] [patterns <pattern>*]
		Enable WoWLAN with the given triggers.
		Each pattern is given as a bytestring with '-' in places where any byte
		may be present, e.g. 00:11:22:-:44 will match 00:11:22:33:44 and
		00:11:22:33:ff:44 etc.

	dev <devname> roc start <freq> <time>

	phy <phyname> set antenna <bitmap> | all | <tx bitmap> <rx bitmap>
		Set a bitmap of allowed antennas to use for TX and RX.
		The driver may reject antenna configurations it cannot support.

	dev <devname> set txpower <auto|fixed|limit> [<tx power in mBm>]
		Specify transmit power level and setting type.

	phy <phyname> set txpower <auto|fixed|limit> [<tx power in mBm>]
		Specify transmit power level and setting type.

	phy <phyname> set distance <distance>
		Set appropriate coverage class for given link distance in meters.
		Valid values: 0 - 114750

	phy <phyname> set coverage <coverage class>
		Set coverage class (1 for every 3 usec of air propagation time).
		Valid values: 0 - 255.

	phy <phyname> set netns <pid>
		Put this wireless device into a different network namespace

	phy <phyname> set rts <rts threshold|off>
		Set rts threshold.

	phy <phyname> set frag <fragmentation threshold|off>
		Set fragmentation threshold.

	dev <devname> set channel <channel> [HT20|HT40+|HT40-]
	phy <phyname> set channel <channel> [HT20|HT40+|HT40-]
	dev <devname> set freq <freq> [HT20|HT40+|HT40-]
	phy <phyname> set freq <freq> [HT20|HT40+|HT40-]
		Set frequency/channel the hardware is using, including HT
		configuration.

	phy <phyname> set name <new name>
		Rename this wireless device.

	dev <devname> set peer <MAC address>
		Set interface WDS peer.

	dev <devname> set noack_map <map>
		Set the NoAck map for the TIDs. (0x0009 = BE, 0x0006 = BK, 0x0030 = VI, 0x00C0 = VO)

	dev <devname> set 4addr <on|off>
		Set interface 4addr (WDS) mode.

	dev <devname> set type <type>
		Set interface type/mode.
		Valid interface types are: managed, ibss, monitor, mesh, wds.

	dev <devname> set meshid <meshid>
	dev <devname> set monitor <flag>*
		Set monitor flags. Valid flags are:
		none:     no special flags
		fcsfail:  show frames with FCS errors
		control:  show control frames
		otherbss: show frames from other BSSes
		cook:     use cooked mode

	dev <devname> set mesh_param <param>=<value> [<param>=<value>]*
		Set mesh parameter (run command without any to see available ones).

	dev <devname> set power_save <on|off>
		Set power save state to on or off.

	dev <devname> set bitrates [legacy-<2.4|5> <legacy rate in Mbps>*] [mcs-<2.4|5> <MCS index>*]
		Sets up the specified rate masks.
		Not passing any arguments would clear the existing mask (if any).

	dev <devname> get mesh_param [<param>]
		Retrieve mesh parameter (run command without any to see available ones).

	dev <devname> get power_save <param>
		Retrieve power save state.

You can omit the 'phy' or 'dev' if the identification is unique,
e.g. "iw wlan0 info" or "iw phy0 info". (Don't when scripting.)

Do NOT screenscrape this tool, we don't consider its output stable.
2019-03-20 13:58:58 +08:00

161 lines
5.2 KiB
Diff

--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -2968,6 +2968,7 @@ struct cfg80211_external_auth_params {
* (as advertised by the nl80211 feature flag.)
* @get_tx_power: store the current TX power into the dbm variable;
* return 0 if successful
+ * @set_antenna_gain: set antenna gain to reduce maximum tx power if necessary
*
* @set_wds_peer: set the WDS peer for a WDS interface
*
@@ -3268,6 +3269,7 @@ struct cfg80211_ops {
enum nl80211_tx_power_setting type, int mbm);
int (*get_tx_power)(struct wiphy *wiphy, struct wireless_dev *wdev,
int *dbm);
+ int (*set_antenna_gain)(struct wiphy *wiphy, int dbi);
int (*set_wds_peer)(struct wiphy *wiphy, struct net_device *dev,
const u8 *addr);
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -1395,6 +1395,7 @@ enum ieee80211_smps_mode {
*
* @power_level: requested transmit power (in dBm), backward compatibility
* value only that is set to the minimum of all interfaces
+ * @max_antenna_gain: maximum antenna gain adjusted by user config (in dBi)
*
* @chandef: the channel definition to tune to
* @radar_enabled: whether radar detection is enabled
@@ -1415,6 +1416,7 @@ enum ieee80211_smps_mode {
struct ieee80211_conf {
u32 flags;
int power_level, dynamic_ps_timeout;
+ int max_antenna_gain;
u16 listen_interval;
u8 ps_dtim_period;
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -2244,6 +2244,9 @@ enum nl80211_commands {
* @NL80211_ATTR_AIRTIME_WEIGHT: Station's weight when scheduled by the airtime
* scheduler.
*
+ * @NL80211_ATTR_WIPHY_ANTENNA_GAIN: Configured antenna gain. Used to reduce
+ * transmit power to stay within regulatory limits. u32, dBi.
+ *
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
@@ -2693,6 +2696,8 @@ enum nl80211_attrs {
NL80211_ATTR_AIRTIME_WEIGHT,
+ NL80211_ATTR_WIPHY_ANTENNA_GAIN,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
--- a/net/mac80211/cfg.c
+++ b/net/mac80211/cfg.c
@@ -2497,6 +2497,19 @@ static int ieee80211_get_tx_power(struct
return 0;
}
+static int ieee80211_set_antenna_gain(struct wiphy *wiphy, int dbi)
+{
+ struct ieee80211_local *local = wiphy_priv(wiphy);
+
+ if (dbi < 0)
+ return -EINVAL;
+
+ local->user_antenna_gain = dbi;
+ ieee80211_hw_config(local, 0);
+
+ return 0;
+}
+
static int ieee80211_set_wds_peer(struct wiphy *wiphy, struct net_device *dev,
const u8 *addr)
{
@@ -3864,6 +3877,7 @@ const struct cfg80211_ops mac80211_confi
.set_wiphy_params = ieee80211_set_wiphy_params,
.set_tx_power = ieee80211_set_tx_power,
.get_tx_power = ieee80211_get_tx_power,
+ .set_antenna_gain = ieee80211_set_antenna_gain,
.set_wds_peer = ieee80211_set_wds_peer,
.rfkill_poll = ieee80211_rfkill_poll,
CFG80211_TESTMODE_CMD(ieee80211_testmode_cmd)
--- a/net/mac80211/ieee80211_i.h
+++ b/net/mac80211/ieee80211_i.h
@@ -1365,6 +1365,7 @@ struct ieee80211_local {
int dynamic_ps_forced_timeout;
int user_power_level; /* in dBm, for all interfaces */
+ int user_antenna_gain; /* in dBi */
enum ieee80211_smps_mode smps_mode;
--- a/net/mac80211/main.c
+++ b/net/mac80211/main.c
@@ -94,7 +94,7 @@ static u32 ieee80211_hw_conf_chan(struct
struct ieee80211_sub_if_data *sdata;
struct cfg80211_chan_def chandef = {};
u32 changed = 0;
- int power;
+ int power, max_power;
u32 offchannel_flag;
offchannel_flag = local->hw.conf.flags & IEEE80211_CONF_OFFCHANNEL;
@@ -151,6 +151,12 @@ static u32 ieee80211_hw_conf_chan(struct
}
rcu_read_unlock();
+ max_power = chandef.chan->max_reg_power;
+ if (local->user_antenna_gain > 0) {
+ max_power -= local->user_antenna_gain;
+ power = min(power, max_power);
+ }
+
if (local->hw.conf.power_level != power) {
changed |= IEEE80211_CONF_CHANGE_POWER;
local->hw.conf.power_level = power;
@@ -626,6 +632,7 @@ struct ieee80211_hw *ieee80211_alloc_hw_
IEEE80211_RADIOTAP_MCS_HAVE_BW;
local->hw.radiotap_vht_details = IEEE80211_RADIOTAP_VHT_KNOWN_GI |
IEEE80211_RADIOTAP_VHT_KNOWN_BANDWIDTH;
+ local->user_antenna_gain = 0;
local->hw.uapsd_queues = IEEE80211_DEFAULT_UAPSD_QUEUES;
local->hw.uapsd_max_sp_len = IEEE80211_DEFAULT_MAX_SP_LEN;
local->user_power_level = IEEE80211_UNSET_POWER_LEVEL;
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -431,6 +431,7 @@ static const struct nla_policy nl80211_p
[NL80211_ATTR_HE_CAPABILITY] = { .type = NLA_BINARY,
.len = NL80211_HE_MAX_CAPABILITY_LEN },
[NL80211_ATTR_AIRTIME_WEIGHT] = NLA_POLICY_MIN(NLA_U16, 1),
+ [NL80211_ATTR_WIPHY_ANTENNA_GAIN] = { .type = NLA_U32 },
};
/* policy for the key attributes */
@@ -2588,6 +2589,20 @@ static int nl80211_set_wiphy(struct sk_b
if (result)
return result;
}
+
+ if (info->attrs[NL80211_ATTR_WIPHY_ANTENNA_GAIN]) {
+ int idx, dbi = 0;
+
+ if (!rdev->ops->set_antenna_gain)
+ return -EOPNOTSUPP;
+
+ idx = NL80211_ATTR_WIPHY_ANTENNA_GAIN;
+ dbi = nla_get_u32(info->attrs[idx]);
+
+ result = rdev->ops->set_antenna_gain(&rdev->wiphy, dbi);
+ if (result)
+ return result;
+ }
if (info->attrs[NL80211_ATTR_WIPHY_ANTENNA_TX] &&
info->attrs[NL80211_ATTR_WIPHY_ANTENNA_RX]) {