set_port_link is required by swconfig to setup link mode.
Here we implemented set_port_link by touching MII PHY registers.
For autoneg enabled case, we set advertise registers to let
autoneg reach the target mode and then retrigger autoneg. For
non autoneg case, we set BMCR register to force PHY enter
desired mode.
This patch have been tested on both MT7620 and MT7621.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
* ramips: add support for Beeline(Sercomm) U-Boot
- Add recipe for several Beeline/Sercomm devices (e.g., Beeline SmartBox
GIGA, Beeline SmartBox Turbo+, Sercomm S3) that appends special header
to a kernel.
- Add device variables KERNEL_LOADADDR, LZMA_TEXT_START. It's also
necessary for the devices mentioned above.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 6240da24f4c1442b0f750f06be512f630b0bc6c8)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: Add support for Beeline SmartBox TURBO+
This PR adds support for router Beeline Smart Box TURBO+.
OEM/ODM Serсomm. Almost identical to Serсomm S3.
Specification
-------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
(cherry picked from commit d1f294521bd8bc462c76e09c57a5c8b0600170cd)
(factory recipe from a2cfe339995467308c9126c3d0f70d2a28aeb073)
(big NAND from e6e5837a625ba09e286a5bde05f2ce581cfbeab7)
(removed nvmem cells, fixed conflicts)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add Sercomm partition map parser
This adds an MTD partition parser for the Sercomm partition table that
is used in some Netgear routers.
This is essentially the same code as proposed in the pull request for
Netgear R6350 support by NOGUCHI Hiroshi <drvlabo@gmail.com>:
https://github.com/openwrt/openwrt/pull/1318
It was originally rejected as it did not seem to work correctly.
However, this was only due the NAND driver transparently shifting pages
to hide bad blocks, which was fixed in commit
527832e54bf3bc4d699a145ae66f34230246f0a9.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[x1@disroot.org: correction from checkpatch.pl]
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
(cherry picked from commit 65e772105f8d5e98a999b836fed794b7415f2741)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: Improve Beeline Smartbox Turbo+ support in lede
Changed switch configuration and a few minor changes.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Co-authored-by: Jan Hoffmann <jan@3e8.eu>
* treewide: remove support for 'DEVICE_COMPAT' variable
This commit removes support for the DEVICE_COMPAT variable due to it
requires relatively few changes.
* Revert "ramips: disable PORT 5 MAC RX/TX flow control by default"
The TX/RX flow control is not the cause of the TX timeouts issue
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: net/mediatek fix logical error
fe_empty_txd() should return `tx_ring_size - 1` on ring empty, and
return 0 on ring full.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: net/mediatek disable eee
This disable eee for mt7530 ports, it causes the link down/up
issue, which happens when connecting to 100Mbit switch
Fixes: FS#1449
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: XiaoYu-C5: reuse ralink-eth driver
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: mt7621.dtsi: add missing pinctrl to ethernet node
Add rgmii1_pins (1st GMAC) and mdio_pins to ethernet node
pinctrl to ensure they are set to correct mode
* ramips: kernel: ralink-eth support mt7621
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: some devices use ralink-eth driver
Also re-added mt7621 hwnat support for some devices.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: AmadeusGhost <amadeus@openjmu.xyz>
* ramips/mt7621: re-added hwnat support
Co-authored-by: LGA1150 <dqfext@gmail.com>
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
