Major changes between OpenSSL 3.0.13 and OpenSSL 3.0.14 [04-Jun-2024]
* Fixed potential use after free after SSL_free_buffers() is called.
[CVE-2024-4741]
* Fixed checking excessively long DSA keys or parameters may be very slow.
[CVE-2024-4603]
* Fixed an issue where some non-default TLS server configurations can cause
unbounded memory growth when processing TLSv1.3 sessions. An attacker may
exploit certain server configurations to trigger unbounded memory growth that
would lead to a Denial of Service. [CVE-2024-2511]
* New atexit configuration switch, which controls whether the OPENSSL_cleanup
is registered when libcrypto is unloaded. This can be used on platforms
where using atexit() from shared libraries causes crashes on exit
Signed-off-by: John Audia <therealgraysky@proton.me>
Import pending patches to set pinconf settings for SPI-NAND pins on
MT7622 identical to what the old proprietary preloader did.
Should further increase the reliability of some SNFI-attached SPI-NAND
flash chips.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update ARM TrustedFirmware-A to the most recent release of
MediaTek downstream patched version released 2024-01-17.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Dont allow x2 read and cache read operations on FM35Q1GA as they seem
to be unstable. Also the Linux drivers does not allow x2 ops.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
At least kmod-fb-tft depends on CONFIG_FB_DEVICE
and can not be activated without it.
This configuration option was added with kernel 6.6,
before this featre was always activated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.
Specifications:
SOC: MT7621 + MT7915
ROM: 128 MiB
RAM: 256 MiB
LED: status *2
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP server IP: 192.168.124.99
Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.
TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
|GND|TX|RX|VCC|
1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
and open a TTL session, enter "reboot", then enter "Y" to confirm.
Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
# tftp 0x80010000 192.168.124.99:initramfs.bin
# bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
partitions if we want to back to stock firmwre due to official
website does not provide download link.
# dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
# dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
# fw_setenv bootargs
# fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
partitions that we backed up in step 4.
# mtd write /tmp/u-boot-env.bin u-boot-env
# mtd write /tmp/firmware.bin firmware
Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This is mostly a cosmetic cleanup. The absence of
the return statement was not causing any problems.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
