Using 2500Base-T SFP modules e.g. on the BananaPi R3 requires manually
disabling auto-negotiation, e.g. using ethtool. While a proper fix
using SFP quirks is being discussed upstream, bring a work-around to
restore user experience to what it was before the switch to the
dedicated SGMII PCS driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport patch allowing to set the MDIO bus clock frequency.
By default the MDIO bus clock runs on 2.5 MHz, allow increasing it
up to 25 MHz.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MT7981 and the upcoming MT7988 have built-in Gigabit Ethernet PHYs.
While they share some design properties with the PHYs present in
MT753x, they do need calibration data from the SoC's efuse.
Add driver to support them. Upstreaming it is planned, but there are
still some ongoing discussions with MediaTek.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport the pinctrl driver for the MT7981 SoC. The driver has also
been submitted upstream and is part of Linux 6.3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport driver for common clocks in MT7981 SoC. The driver has also
been submitted upstream and became part of Linux 6.3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace patches for MediaTek Ethernet driver SGMII/SerDes unit with
their corresponding upstream patches. Not all of the patches in our
tree went upstream as-is, some are slightly different implementations,
and they require the phylink_pcs helpers now made available.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It isn't feasible to literally backport all upstream phylink_pcs changes
down to Linux 5.15: It's just too many patches, and many downstream
drivers and hacks are likely to break. We are too close to branching off
to risk this, and it's also just too much work.
Instead just add helper functions used by modern PCS drivers while keeping
the original functions instact as well. While this may add a kilobyte or
two of extra kernel size, it has the advantage that we get the best of both
worlds: None of the existing codepaths are touched, but yet we have the
option to backport singular improvements to Ethernet drivers where needed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If intel ibt enable. It will cause kernel panic
when load "compat.ko" kernel module(a part of cfg80211)
Signed-off-by: Jax Jiang <jax.jiang.007@gmail.com>
RISC-V is a new CPU architecture aimed to be fully free and open. This
target will add support for it, based on 5.15.
Supports running on:
- HiFive Unleashed - FU540, first generation
- HiFive Unmatched - FU740, current latest generation, PCIe
SD-card images are generated, where the partitions are required to have
specific type codes. As it is commonplace nowadays, OpenSBI is used as the
first stage, with U-boot following as the proper bootloader.
Specifications:
HiFive Unleashed:
- CPU: SiFive FU540 quad-core RISC-V (U54, RV64IMAFDC or RV64GC)
- Memory: 8Gb
- Ethernet: 1x 10/100/1000
- Console: via microUSB
HiFive Unmatched:
- CPU: SiFive FU740 quad-core RISC-V (U74, RV64IMAFDCB or RV64GCB)
- Memory: 16Gb
- Ethernet: 1x 10/100/1000
- USB: 4x USB 3.2
- PCIe: - 1x PCIe Gen3 x8
- 1x M.2 key M (PCIe x4)
- 1x M.2 Key E (PCIe x1 / USB2.0)
- Console: via microUSB
Installation:
Standard SD-card installation via dd-ing the generated image to
an SD-card of at least 256Mb.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The set_spi_clock_speed() function is not used, this causes a compile
warning which results in a build error with -WError.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This set the CONFIG_FRAME_WARN option depending on some target settings.
It will use the default from the upstream kernel and not the hard coded
value of 1024 now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This new option (default N) will generate prompts building with OpenWrt
configs that set CONFIG_KERNEL_DYNAMIC_DEBUG=y. Fix this by adding the
disabled option to the generic config.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Make ar8216/8327 swconfig driver modularizable and add
entry to the netdevices.mk kernel modules file.
Fixes: #11250
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Use scratch buffer for DMA operetations. Passing a pointer to a stack
variable won't work and results in bogus bit flips being reported.
Patch was submitted upstream and is part of Linux 6.3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
According to SinoVoip up to 3A @ 3.3V are available for both
SFP modules together. Raise energy limit from 1W (default) to 3W,
however, be aware that using modules consuming more than 1W will
require active cooling!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import commit "ubi: Fix failure attaching when vid_hdr offset equals to
(sub)page size" which did not yet make it to stable upstream Linux trees.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
