At least kmod-fb-tft depends on CONFIG_FB_DEVICE
and can not be activated without it.
This configuration option was added with kernel 6.6,
before this featre was always activated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.
Specifications:
SOC: MT7621 + MT7915
ROM: 128 MiB
RAM: 256 MiB
LED: status *2
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP server IP: 192.168.124.99
Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.
TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
|GND|TX|RX|VCC|
1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
and open a TTL session, enter "reboot", then enter "Y" to confirm.
Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
# tftp 0x80010000 192.168.124.99:initramfs.bin
# bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
partitions if we want to back to stock firmwre due to official
website does not provide download link.
# dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
# dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
# fw_setenv bootargs
# fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
partitions that we backed up in step 4.
# mtd write /tmp/u-boot-env.bin u-boot-env
# mtd write /tmp/firmware.bin firmware
Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This is mostly a cosmetic cleanup. The absence of
the return statement was not causing any problems.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
devm_gpiod_get_from_of_node() was removed since linux 6.2.
devm_fwnode_gpiod_get() is the recommended replacement.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Build and package driver for MediaTek PCIe 5G WWAN modem T7xx device
available in Linux 6.1 and 6.6 as kmod-mtk-t7xx.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the 'tmon' packages. This is as a tool to help visualize,
tune, and test the complex thermal subsystem.
We get a compile warning for the tool that the printf format does not
fit. This commit contains a patch that fixes this warning. This patch
has also been sent upstream to the Linux kernel [1].
Links:
[1] https://lore.kernel.org/all/20231204141335.2798194-1-fe@dev.tdt.de/
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
- use Makefile.perf to prevent overriding MAKEFLAGS
- fix path to PKG_CONFIG
- link libstdc++ statically (only used for demangling)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adds MediaTek MT7916AN and Cypress CYW43455 (Raspberry Pi 5) devices.
a34977c devices: add device id for Cypress CYW43455
3eb34df devices: add device id for MediaTek MT7916AN
This contains an ABI change, increase the ABI version too.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
