The current target code is too chaotic, the patches are
messy and disorderly, and there are still many duplicate
code. Pack it back to half a year ago.
MediaTek's ARM Trusted Firmware v2.7+ allows the images inside a FIP
structure to be compressed. Make use of that for boards with NOR flash.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The updated sources bring support for the MT798x Filogic SoC family.
Add builds for MT7986 with most supported storage types, each for DDR3
and DDR4 configurations.
A better solution for skipping bad blocks on SPI-NAND connected via the
SNFI interface has been implemented upstream, so drop local patch.
Add pending patches [1] and [2] to fix boot on existing MT7622 boards.
Tested on BananaPi BPi-R64 (SDMMC, eMMC, SPI-NAND), Linksys E8450 and
Ubiquiti UniFi 6 LR as well as upcoming Bananapi BPi-R3 board for which
support will be added in future patches.
[1]: https://github.com/mtk-openwrt/arm-trusted-firmware/pulls/#3
[2]: https://github.com/mtk-openwrt/arm-trusted-firmware/pulls/#4
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
As anyway only the default is called now we can as well also just remove
the override for Build/Configure.
Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of relying on dtc being provided by the build host use the
dtc from $(LINUX_DIR) similar to how it's done also in u-boot.mk.
For this to work kernel.mk now needs to be included before
trusted-firmware-a.mk, add this include to all affected packages.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch to skip bad blocks when reading from SPI-NAND. This is needed
in case erase block(s) early in the flash inside the FIP area are bad
and hence need to be skipped in order to be able to boot on such damaged
chips.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With this change you need have swig and libpython3-dev installed on
your host, which should be done already.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The rk356x SoC does not have Rockchip miniloader at all.
However, it has following features (hope you can enjoy):
-- Support boot Android format image only
-- Support gpt/misc compulsory verification
-- Full-closed binary and uboot can't ntr it
This reverts commit 2c340abaf1.
The PKG_LICENSE field was missing.
While at it, normalize the Makefile a bit.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Co-authored-by: Paul Spooren <mail@aparcar.org>
* uboot-rockchip: Fix doornet1dts
The dts refers to the official website uboot startup parameters
`arch/arm/mach-rockchip/rk3328/rk3328.c`---Fix boot order parameters,It is helpful for other devices to start emmc and sd normally
* Update 104-rockchip-rk3328-Add-support-for-EmbedFire-DoorNet1.patch
Previously, grub2 was hardcoded to always look on "hd0" for the
kernel.
This works well when the system only had a single disk.
But if there was a second disk/stick present, it may have look
on the wrong drive because of enumeration races.
This patch utilizes grub2 search function to look for a filesystem
with the label "kernel". This works thanks to existing setup in
scripts/gen_image_generic.sh. Which sets the "kernel" label on
both the fat and ext4 filesystem variants.
Signed-off-by: Jax Jiang <jax.jiang.007@gmail.com>
Suggested-by: Alberto Bursi <bobafetthotmail@gmail.com> (MX100 WA)
(word wrapped, slightly rewritten commit message, removed MX100 WA)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* Rockchip:Fix dtsi of doornet2
phy:
Modify phy timing;The manufacturer's board requires two timing modes: 125m and 25m ---stmmac_mdio.c stmmac_main.c
Among them, stmmac_main.c is added with 1.5 reset, and the compilation of other devices is not affected
emmc:
In emmc hs400 mode, the performance test effect is the same as hs200, so it is safer to reduce hs200
* Rockchip:Add doornet2 to overclock to 2.2GHz/1.8GHz
* Create 105-rockchip-rk3399-Add-support-for-EmbedFire-DoorNet2.patch
Modify the startup method: SD starts first, which is convenient for saving bricks. If there is no system in SD, it will automatically jump to the next emmc boot
* Update with kernel 5.4
* Update 992-rockchip-rk3399-overclock-to-2.2-1.8-GHz-for-NanoPi4.patch
Subtarget-specific files under 'uboot-envtools' package are supported
since 6f3a05ebb0 ("uboot-envtools: support uci-default config also per
subtargets").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
