Hardware
--------
SOC: MediaTek MT7988A (4x Cortex-A73)
RAM: 4 GiB DDR4
Flash: 128 MiB Winbond SPI-NAND
MMC: 8 GiB eMMC *or* microSD (cannot be used both)
ETH: 4x 1GE (1x WAN, 3x LAN)
2x SFP+ (10G, 5G, 2.5G, 1G)
USB: on-board USB 3.2 4-port hub
1x USB 3.2 port (type A connector)
1x M.2 for 4G/5G modem
2x mPCIe for additional modems
WiFi: optional MediaTek MT7996 Wi-Fi 7 module
(using 2x PCIe gen3 x2 on the mPCIe slots and 12V power)
Installation
------------
1. Decompress and write the sdcard image to a micro SD card and use that
to boot the R4 (both dip switches in upper position).
2. Use the bootloader menu accessible via the serial console to install
to SPI-NAND.
3. Switch to boot from SPI-NAND and install to eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.
Specifications:
SOC: MT7621 + MT7915
ROM: 128 MiB
RAM: 256 MiB
LED: status *2
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP server IP: 192.168.124.99
Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.
TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
|GND|TX|RX|VCC|
1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
and open a TTL session, enter "reboot", then enter "Y" to confirm.
Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
# tftp 0x80010000 192.168.124.99:initramfs.bin
# bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
partitions if we want to back to stock firmwre due to official
website does not provide download link.
# dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
# dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
# fw_setenv bootargs
# fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
partitions that we backed up in step 4.
# mtd write /tmp/u-boot-env.bin u-boot-env
# mtd write /tmp/firmware.bin firmware
Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The previous offsets did also work, as they've wrapped back to 0x0.
However, in reality the environment starts at offset 0x0 of the
u-boot-env MMC partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
SoC: MediaTek MT7981BA
RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC: 8GB eMMC (Samsung 8GTF4R)
ETH: 1000Base-T LAN (ePHY)
2500Base-T WAN (MaxLinear GPY211C)
BTN: 1x Reset Button
LED: System (blue/white)
VPN (white)
USB: 1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
Don't connect 3.3V!
Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!
Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: fix sysupgrade for gl-mt6000
* mediatek: add u-boot support for gl-mt6000
* mediatek: fix lan port for gl-mt6000
* mediatek: fix wifi mac for gl-mt6000
* build: fix incomplete initramfs compression options
Requires: tools/lz4, tools/lzop
complete the wiring so that these options work:
* `CONFIG_KERNEL_INITRAMFS_COMPRESSION_LZO`
* `CONFIG_KERNEL_INITRAMFS_COMPRESSION_LZ4`
Signed-off-by: Tony Butler <spudz76@gmail.com>
[remove blocking dependencies for separate ramdisk, fix lzop options]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* include: sync with upstream
* toolchain/binutils: add support for version 2.40
Release notes:
https://sourceware.org/pipermail/binutils/2023-January/125671.html
Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
* toolchain/gcc: switch to version 12 by default
Also fix build error with gcc 12.
* toolchain/nasm: update to 2.16.01
ChangeLog:
Version 2.16.01
_This is a documentation update release only._
(*) Fix the creation of the table of contents in the HTML version of
the documentation.
Version 2.16
(*) Support for the `rdf' format has been discontinued and all the
RDOFF utilities has been removed.
(*) The `--reproducible' option now leaves the filename field in the
COFF object format blank. This was always rather useless since
it is only 18 characters long; as such debug formats have to
carry their own filename information anyway.
(*) Fix handling of MASM-syntax reserved memory (e.g. `dw ?') when
used in structure definitions.
(*) The preprocessor now supports functions, which can be less
verbose and more convenient than the equivalent code implemented
using directives. See section 4.4.
(*) Fix the handling of `%00' in the preprocessor.
(*) Fix incorrect handling of path names affecting error messages,
dependency generation, and debug format output.
(*) Support for the RDOFF output format and the RDOFF tools have
been removed. The RDOFF tools had already been broken since at
least NASM 2.14. For flat code the ELF output format
recommended; for segmented code the `obj' (OMF) output format.
(*) New facility: preprocessor functions. Preprocessor functions,
which are expanded similarly to single-line macros, can greatly
simplify code that in the past would have required a lengthy
list of directives and intermediate macros. See section 4.4.
(*) Single-line macros can now declare parameters (using a `&&'
prefix) that creates a quoted string, but does _not_ requote an
already quoted string. See section 4.2.1.
(*) Instruction table updated per public information available as of
November 2022.
(*) All warnings in the preprocessor have now been assigned warning
classes. See appendix A.
(*) Fix the invalid use of `RELA'-type relocations instead of `REL'-
type relocations when generating DWARF debug information for the
`elf32' output format.
(*) Fix the handling `at' in `istruc' when the structure contains
local labels. See section 5.9.2.
(*) When assembling with `--reproducible', don't encode the filename
in the COFF header for the `coff', `win32' or `win64' output
formats. The COFF header only has space for an 18-character
filename, which makes this field rather useless in the first
place. Debug output data, if enabled, is not affected.
(*) Fix incorrect size calculation when using MASM syntax for non-
byte reservations (e.g. `dw ?'.)
(*) Allow forcing an instruction in 64-bit mode to have a (possibly
redundant) REX prefix, using the syntax `{rex}' as a prefix.
(*) Add a `{vex}' prefix to enforce VEX (AVX) encoding of an
instruction, either using the 2- or 3-byte VEX prefixes.
(*) The `CPU' directive has been augmented to allow control of
generation of VEX (AVX) versus EVEX (AVX-512) instruction
formats, see section 7.11.
(*) Some recent instructions that previously have been only
available using EVEX encodings are now also encodable using VEX
(AVX) encodings. For backwards compatibility these encodings are
not enabled by default, but can be generated either via an
explicit `{vex}' prefix or by specifying either `CPU LATEVEX' or
`CPU NOEVEX'; see section 7.11.
(*) Document the already existing `%unimacro' directive. See section
4.5.12.
(*) Fix a code range generation bug in the DWARF debug format
(incorrect information in the `DW_AT_high_pc' field) for the ELF
output formats. This bug happened to cancel out with a bug in
older versions of the GNU binutils linker, but breaks with other
linkers and updated or other linkers that expect the spec to be
followed.
(*) Fix segment symbols with addends, e.g. `jmp _TEXT+10h:0' in
output formats that support segment relocations, e.g. the `obj'
format.
(*) Fix various crashes and hangs on invalid input.
Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
* toolchain: musl: Fix symbol loading in gdb
Fix DT_DEBUG handling on MIPS in musl libc.
With this change gdb will load the symbol files for shared libraries on MIPS too.
This patch was taken from this thread: https://www.openwall.com/lists/musl/2022/01/09/4
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* tools: sync with upstream
* build: fix issues with targets installed via feeds
- fix including modules.mk when a target is being replaced
- fix calling make targets from target/linux
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* package: sync with upstream
Signed-off-by: Tony Butler <spudz76@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Co-authored-by: Tony Butler <spudz76@gmail.com>
Co-authored-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Co-authored-by: Felix Fietkau <nbd@nbd.name>
Similar to the implementation for the BPi-R3 use the same logic also
for determining the device to look for the U-Boot environment of the
BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix accessing the environment in case no OS is installed on the flash
media selected for boot as this is possible when booting initramfs.
In case of relying on the device specified to be mounted as rootfs to
be present, rather just use the kernel cmdline 'root' variable as a
hint to decide where to read/write the U-Boot environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Create new mediatek_filogic file and add entries for environment on
MMC, UBI and NOR for the Bananapi BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Subtarget-specific files under 'uboot-envtools' package are supported
since 6f3a05ebb0 ("uboot-envtools: support uci-default config also per
subtargets").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for Beeline(Sercomm) U-Boot
- Add recipe for several Beeline/Sercomm devices (e.g., Beeline SmartBox
GIGA, Beeline SmartBox Turbo+, Sercomm S3) that appends special header
to a kernel.
- Add device variables KERNEL_LOADADDR, LZMA_TEXT_START. It's also
necessary for the devices mentioned above.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 6240da24f4c1442b0f750f06be512f630b0bc6c8)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: Add support for Beeline SmartBox TURBO+
This PR adds support for router Beeline Smart Box TURBO+.
OEM/ODM Serсomm. Almost identical to Serсomm S3.
Specification
-------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
(cherry picked from commit d1f294521bd8bc462c76e09c57a5c8b0600170cd)
(factory recipe from a2cfe339995467308c9126c3d0f70d2a28aeb073)
(big NAND from e6e5837a625ba09e286a5bde05f2ce581cfbeab7)
(removed nvmem cells, fixed conflicts)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: add Sercomm partition map parser
This adds an MTD partition parser for the Sercomm partition table that
is used in some Netgear routers.
This is essentially the same code as proposed in the pull request for
Netgear R6350 support by NOGUCHI Hiroshi <drvlabo@gmail.com>:
https://github.com/openwrt/openwrt/pull/1318
It was originally rejected as it did not seem to work correctly.
However, this was only due the NAND driver transparently shifting pages
to hide bad blocks, which was fixed in commit
527832e54bf3bc4d699a145ae66f34230246f0a9.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[x1@disroot.org: correction from checkpatch.pl]
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
(cherry picked from commit 65e772105f8d5e98a999b836fed794b7415f2741)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: Improve Beeline Smartbox Turbo+ support in lede
Changed switch configuration and a few minor changes.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Co-authored-by: Jan Hoffmann <jan@3e8.eu>
The difference between flashing:
Interrupt U-Boot and run these commands:
setenv bootcmd "setenv mtdids nand0=nand0 && set mtdparts
mtdparts=nand0:0xDC00000@0x2400000(firmware) && ubi part firmware &&
ubi read 0x44000000 kernel 0x6e0000 && bootm"
saveenv
[mac80211]
5b29614 mac80211: another fix for the sta connection monitor
1ed6eb1 mac80211: backport sched_set_fifo_low
cba4120 mac80211: add support for specifying a per-device scan list
e0d482f rt2x00: mt7620: differentiate based on SoC's CHIP_VER
[package]
amd64-microcode/intel-microcode/linux-firmware: update version
[mac80211]
ca5ee6e mac80211: Fix potential endless loop
2c14710 mac80211: add more AQL fixes/improvements
91fb3ce mac80211: remove an obsolete patch that is no longer doing anything useful
acf1733 mac80211: add preliminary support for enabling 802.11ax in config
d717343 mac80211: update encap offload patches to the latest version
673062f mac80211: allow bigger A-MSDU sizes in VHT, even if HT is limited
caf7277 mac80211: do not allow bigger VHT MPDUs than the hardware supports
cd36c0d mac80211: select the first available channel for 5GHz interfaces
1c6d456 mac80211: fix regression in station connection monitor optimization
4bd7689 mac80211: update sta connection monitor regression fix
[target]
Sync: at91, ath25, ath79, lantiq, mediatek, mvebu.
kernel: bump to 4.14.193, 4.19.138, 5.4.59 (#5350)
431fb8c mac80211: add AQL improvements
6bdd4c9 mac80211: add missing backports for building with 4.14 kernels
0106820 mac80211: add missing return code checks in AQL improvements
e7f7101 mac80211: rework encapsulation offload support
[package]
base-files: add function for generating random MAC
dnsmasq: abort dhcp_check on interface state
boot: sync upstream source code
ath10k-ct-firmware/mt76/sch_cake: update to latest git HEAD
[script]
download: add China Mirror Station
[target]
Sync: arc770, ath79, bcm63xx, kirkwood, lantiq, layerscape,
mediatek, mvebu, octeon, oxnas, pistachio, uml
Sync most of the target patches.
Run-compiled-on: ipq40xx (4.19 & 5.4), ramips
