Introduced with Linux 6.7, in commit:
5c2f7727d437 ("mtd: mtdpart: check for subpartitions parsing result"),
when a parser returns an error, this will be passed up, and
consequently, all parent mtd partitions get torn down.
Adjust the mtdsplit_uimage driver to only return an error if there is a
critical problem in reading from the mtd device or allocating memory.
Otherwise return 0 to indicate that no partitions were found.
Also add logging to indicate what went wrong.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
New stm32 target introduces support for stm32mp1 based devices.
For now it includes an initial support of the STM32MP135F-DK device.
The specifications bellow only list supported features.
Specifications
--------------
SOC: STM32MP135FAF7
RAM: 512 MiB
Storage: SD Card
Ethernet: 2x 100 Mbps
Wireless: 2.4GHz Cypress CYW43455 (802.11b/g/n)
LEDs: Heartbeat (Blue)
Buttons: 1x Reset, 1x User (USER2)
USB: 4x 2.0 Type-A
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target adds support for the Allwinner D1 RISC-V based SoCs.
- RISC-V single-core T-Head C906 (RV64GCV)
- Tensilica HiFi4 DSP
- DDR2/DDR3 support
- 10/100/1000M ethernet
- usual peripherals like USB2, SPI, I2C, PWM, etc.
Installation:
Standard SD-card installation via dd-ing the generated image to
an SD-card of at least 256Mb.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This target adds support for the StarFive JH7100 and JH7110 SoCs,
based on 6.12, as well as a couple boards equipped with these.
Installation:
Standard SD-card installation via dd-ing the generated image to
an SD-card of at least 256Mb.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Allow the armsr target to be built with a 6.12 kernel
when CONFIG_TESTING_KERNEL is set.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compared to v6.6 the patches to add "10gbase-r", "2500base-x",
"1000base-x", and "10g-qxgmii" modes have not been ported yet. They do
not apply cleanly to the new PCS driver. As the currently supported
hardware does not use those modes, it is not possible to test them at
this time.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 6.12 testing kernel for ath79 target is ready now.
Tested on AR9344 (ath79/nand) and QCA9531 (ath79/generic).
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add kernel package for DesignWare I2C platform controller.
This controller is used on the RP1 SoC found on RPi 5 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* the variant with 2.5G PHY instead of LAN SFP is called '2p5'
upstream and 'poe' in our downstream Linux DT. Use the right
DTS depending on the kernel version and set an additional
compatible.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MediaTek Ethernet PHY drivers are going to be used by multiple
targets (airoha, mediatek, ramips). Add generic backports of changes
required for recently added Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Updating the spi-qpic-snand driver with the latest patches sent
upstream and remove custom patches.
These patches add error handling fixes, use of right read location in
read ops, removal of unused variable, ability to read user config and
nand chip requirements, and support for 8bits ECC strength.
Tested on: Gl.iNet GL-B3000 & Linksys MR5500, MX2000, MX5500, SPNMX56
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
For kernel 6.12 there is a warning causing an error.
Swapping the arguments solves the problem.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
