Add a patch to allow modification of the PHY LED configuration. This is
required for boards, where the reset configuration of LED functions is
incompatibe with the usage of the device LEDs.
This is the case for the ASUS TUF-AX4200 Wireless router. It requires
modification of the LED configuration because as the WAN LED on the
front of the device is driven by the PHY. Without patching, it would
only illuminate in case the Link speed is 100 Mbit/s.
Signed-off-by: David Bauer <mail@david-bauer.net>
The ASUS TUF-AX4200 bootloader adds invalid parameters for the rootfs.
Without overwriting the cmdline, the kernel crashes when trying to
attach the rootfs, as OpenWrt uses a different partition than the vendor
OS.
Signed-off-by: David Bauer <mail@david-bauer.net>
This flash-chip is used on the Asus TUF-AX4200 and TUF-AX6000 routers.
As the filogic target only uses kernel 5.15, skip the 5.10 backport.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
* 2.4 GHz: MediaTek MT7622BV
* 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
115200n8
* Power: 12 VDC, 2.5 A
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.100
tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
bootm
Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
moment. If connected to a multi-gig port the speed has to be manually
set to 1G/full either for the switch port or in OpenWrt. For example
add the following to /etc/rc.local to set it on boot:
/usr/sbin/ethtool -s wan speed 1000 duplex full
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar
* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
Image creation code for this device
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port, adjust partition layout and image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
Import some accepted and pending upstream patches for mtk_eth_soc,
replacing some semantically equivalent local patches and fixing issues
when operating the PCS in 1G SGMII mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
