* armvirt: copy config files from 5.10
Copy config files from 5.10.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* armvirt: refresh 5.15 config
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* armvirt: move common symbols from subtarget to target config
These new symbols are common for all subtargets and
can be moved into target config.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Co-authored-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Co-authored-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This Kernel option allows to run OpenWrt witin a `firecracker` micro VM.
Firecracker is a KVM-based tool for superfast booting VMs on x86_64 and
aarch64. It makes rootfs available to the guest as a virtio-mmio device
and passes its address via the kernel cmdline. A kernel without
CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES will not recognize the rootfs
virtio-mmio device.
Suggested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Co-authored-by: Paul Spooren <mail@aparcar.org>
* armvirt: switch to Kernel 5.10
Armvirt is a development and testing platform and should therefore use
the latest OpenWrt Kernel by default.
Tested via qemu.
Acked-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
* armvirt: add 5.15 as testing kernel
Add 5.15 as testing kernel.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Co-authored-by: Paul Spooren <mail@aparcar.org>
Co-authored-by: Aleksander Jan Bajkowski <olek2@wp.pl>
According to MediaTek MT7688 Datasheet v1.4, as well as the MT7628
counterpart, the memory controller reset bit (MC_RST) is 10, not 20.
Reset bit 20 is used for for UART 2 (UART2_RST).
Please note: Due to the lack of hardware, I was not able to test this
change.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
set_port_link is required by swconfig to setup link mode.
Here we implemented set_port_link by touching MII PHY registers.
For autoneg enabled case, we set advertise registers to let
autoneg reach the target mode and then retrigger autoneg. For
non autoneg case, we set BMCR register to force PHY enter
desired mode.
This patch have been tested on both MT7620 and MT7621.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Fixes: #10275
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: move mtk flow offload patches to backport-5.15
They were accepted upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport upstream mtk_eth_soc patches
Includes MT7986 ethernet support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Co-authored-by: Felix Fietkau <nbd@nbd.name>
