mirror of
https://github.com/coolsnowwolf/lede.git
synced 2025-04-18 17:33:31 +00:00
ipq806x: add support for Buffalo WXR-2533DHP
This commit is contained in:
coolsnowwolf
parent
994030e6a4
commit
a3057c7d65
@ -20,7 +20,7 @@ DEFAULT_PACKAGES += \
|
||||
kmod-ata-core kmod-ata-ahci kmod-ata-ahci-platform \
|
||||
kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
|
||||
kmod-usb3 kmod-usb-dwc3-of-simple kmod-usb-phy-qcom-dwc3 \
|
||||
kmod-ath10k wpad-basic \
|
||||
kmod-ath10k-ct wpad-basic \
|
||||
uboot-envtools
|
||||
|
||||
$(eval $(call BuildTarget))
|
||||
|
||||
@ -11,6 +11,10 @@ board=$(board_name)
|
||||
boardname="${board##*,}"
|
||||
|
||||
case "$board" in
|
||||
buffalo,wxr-2533dhp)
|
||||
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:white:wireless" "phy0tpt"
|
||||
ucidef_set_led_switch "wan" "WAN" "${boardname}:white:internet" "switch0" "0x20"
|
||||
;;
|
||||
compex,wpq864)
|
||||
ucidef_set_led_usbport "usb" "USB" "wpq864:green:usb" "usb1-port1" "usb2-port1"
|
||||
ucidef_set_led_usbport "pcie-usb" "PCIe USB" "wpq864:green:usb-pcie" "usb3-port1"
|
||||
|
||||
@ -12,6 +12,7 @@ board_config_update
|
||||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
buffalo,wxr-2533dhp |\
|
||||
compex,wpq864 |\
|
||||
netgear,d7800 |\
|
||||
netgear,r7500 |\
|
||||
@ -21,6 +22,11 @@ tplink,vr2600v)
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
|
||||
;;
|
||||
qcom,ipq8064-ap161)
|
||||
ucidef_set_interface_lan "eth1 eth2"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "1:lan" "2:lan" "3u@eth1" "6:wan" "4u@eth0"
|
||||
;;
|
||||
linksys,ea8500)
|
||||
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
||||
ucidef_add_switch "switch0" \
|
||||
|
||||
@ -1,46 +0,0 @@
|
||||
#!/bin/sh
|
||||
# Copyright (C) 2016 Henryk Heisig hyniu@o2.pl
|
||||
|
||||
. /lib/functions/leds.sh
|
||||
|
||||
boot="$(get_dt_led boot)"
|
||||
failsafe="$(get_dt_led failsafe)"
|
||||
running="$(get_dt_led running)"
|
||||
upgrade="$(get_dt_led upgrade)"
|
||||
|
||||
set_state() {
|
||||
status_led="$boot"
|
||||
|
||||
case "$1" in
|
||||
preinit)
|
||||
status_led_blink_preinit
|
||||
;;
|
||||
failsafe)
|
||||
status_led_off
|
||||
[ -n "$running" ] && {
|
||||
status_led="$running"
|
||||
status_led_off
|
||||
}
|
||||
status_led="$failsafe"
|
||||
status_led_blink_failsafe
|
||||
;;
|
||||
preinit_regular)
|
||||
status_led_blink_preinit_regular
|
||||
;;
|
||||
upgrade)
|
||||
[ -n "$running" ] && {
|
||||
status_led="$running"
|
||||
status_led_off
|
||||
}
|
||||
status_led="$upgrade"
|
||||
status_led_blink_preinit_regular
|
||||
;;
|
||||
done)
|
||||
status_led_off
|
||||
[ -n "$running" ] && {
|
||||
status_led="$running"
|
||||
status_led_on
|
||||
}
|
||||
;;
|
||||
esac
|
||||
}
|
||||
@ -1,5 +1,21 @@
|
||||
#!/bin/sh
|
||||
|
||||
# xor multiple hex values of the same length
|
||||
xor() {
|
||||
local val
|
||||
local ret="0x$1"
|
||||
local retlen=${#1}
|
||||
|
||||
shift
|
||||
while [ -n "$1" ]; do
|
||||
val="0x$1"
|
||||
ret=$((ret ^ val))
|
||||
shift
|
||||
done
|
||||
|
||||
printf "%0${retlen}x" "$ret"
|
||||
}
|
||||
|
||||
ath10kcal_die() {
|
||||
echo "ath10cal: " "$*"
|
||||
exit 1
|
||||
@ -28,12 +44,29 @@ ath10kcal_extract() {
|
||||
ath10kcal_die "failed to extract calibration data from $mtd"
|
||||
}
|
||||
|
||||
ath10kcal_patch_mac() {
|
||||
ath10kcal_patch_mac_crc() {
|
||||
local mac=$1
|
||||
local mac_offset=6
|
||||
local chksum_offset=2
|
||||
local xor_mac
|
||||
local xor_fw_mac
|
||||
local xor_fw_chksum
|
||||
|
||||
[ -z "$mac" ] && return
|
||||
|
||||
xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
||||
xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}"
|
||||
|
||||
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
|
||||
|
||||
xor_mac=${mac//:/}
|
||||
xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}"
|
||||
|
||||
xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
||||
xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac)
|
||||
|
||||
printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \
|
||||
dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2
|
||||
}
|
||||
|
||||
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
||||
@ -43,53 +76,72 @@ ath10kcal_patch_mac() {
|
||||
|
||||
board=$(board_name)
|
||||
|
||||
|
||||
case "$FIRMWARE" in
|
||||
"ath10k/pre-cal-pci-0000:01:00.0.bin")
|
||||
case $board in
|
||||
buffalo,wxr-2533dhp)
|
||||
ath10kcal_extract "ART" 4096 12064
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_binary ART 30)
|
||||
;;
|
||||
linksys,ea8500)
|
||||
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
||||
ath10kcal_extract "art" 4096 12064
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +1)
|
||||
;;
|
||||
nec,wg2600hp)
|
||||
ath10kcal_extract "ART" 4096 12064
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary PRODUCTDATA 12) +1)
|
||||
;;
|
||||
netgear,d7800 |\
|
||||
netgear,r7500v2 |\
|
||||
netgear,r7800)
|
||||
ath10kcal_extract "art" 4096 12064
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 6) +1)
|
||||
;;
|
||||
tplink,c2600)
|
||||
ath10kcal_extract "radio" 4096 12064
|
||||
# ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 8) -1)
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary default-mac 8) -1)
|
||||
;;
|
||||
nec,wg2600hp |\
|
||||
tplink,vr2600v)
|
||||
ath10kcal_extract "ART" 4096 12064
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary default-mac 0) -1)
|
||||
;;
|
||||
zyxel,nbg6817)
|
||||
ath10kcal_extract "0:ART" 4096 12064
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) +1)
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
"ath10k/pre-cal-pci-0001:01:00.0.bin")
|
||||
case $board in
|
||||
buffalo,wxr-2533dhp)
|
||||
ath10kcal_extract "ART" 20480 12064
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_binary ART 24)
|
||||
;;
|
||||
linksys,ea8500)
|
||||
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
||||
ath10kcal_extract "art" 20480 12064
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +2)
|
||||
;;
|
||||
nec,wg2600hp)
|
||||
ath10kcal_extract "ART" 20480 12064
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_binary PRODUCTDATA 12)
|
||||
;;
|
||||
netgear,d7800 |\
|
||||
netgear,r7500v2 |\
|
||||
netgear,r7800)
|
||||
ath10kcal_extract "art" 20480 12064
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 6) +2)
|
||||
;;
|
||||
tplink,c2600)
|
||||
ath10kcal_extract "radio" 20480 12064
|
||||
# ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 8) -2)
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_binary default-mac 8)
|
||||
;;
|
||||
nec,wg2600hp |\
|
||||
tplink,vr2600v)
|
||||
ath10kcal_extract "ART" 20480 12064
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_binary default-mac 0)
|
||||
;;
|
||||
zyxel,nbg6817)
|
||||
ath10kcal_extract "0:ART" 20480 12064
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
|
||||
@ -9,29 +9,23 @@ PHYNBR=${DEVPATH##*/phy}
|
||||
. /lib/functions.sh
|
||||
. /lib/functions/system.sh
|
||||
|
||||
board=$(board_name)
|
||||
OPATH=${DEVPATH##/devices/platform/}
|
||||
OPATH=${OPATH%%/ieee*}
|
||||
|
||||
case "$board" in
|
||||
linksys,ea8500)
|
||||
echo $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) $(($PHYNBR + 1)) ) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
nec,wg2600hp)
|
||||
echo $(macaddr_add $(mtd_get_mac_binary PRODUCTDATA 12) $((1 - $PHYNBR)) ) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
netgear,d7800 |\
|
||||
netgear,r7500v2 |\
|
||||
netgear,r7800)
|
||||
echo $(macaddr_add $(mtd_get_mac_binary art 6) $(($PHYNBR + 1)) ) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
tplink,c2600)
|
||||
echo $(macaddr_add $(mtd_get_mac_binary default-mac 8) $(($PHYNBR - 1)) ) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
tplink,vr2600v)
|
||||
echo $(macaddr_add $(mtd_get_mac_binary default-mac 0) $(($PHYNBR - 1)) ) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
zyxel,nbg6817)
|
||||
echo $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) $((1 - $PHYNBR)) ) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
*)
|
||||
;;
|
||||
esac
|
||||
# 10 radios is enough for anyone!
|
||||
for i in `seq 0 9`;
|
||||
do
|
||||
BUS=`uci get wireless.@wifi-device[$i].path`
|
||||
if [ "$BUS " == "$OPATH " ]
|
||||
then
|
||||
PHYNAME=${DEVPATH##*ieee80211/}
|
||||
NPHYNAME=`uci get wireless.@wifi-device[$i].phyname`
|
||||
if [ "$NPHYNAME " != " " ]
|
||||
then
|
||||
if [ "$PHYNAME " != "$NPHYNAME " ]
|
||||
then
|
||||
iw $PHYNAME set name $NPHYNAME
|
||||
fi
|
||||
fi
|
||||
fi
|
||||
done
|
||||
|
||||
139
target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh
Normal file
139
target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh
Normal file
@ -0,0 +1,139 @@
|
||||
#!/bin/sh
|
||||
# Copyright (C) 2018 OpenWrt.org
|
||||
#
|
||||
|
||||
. /lib/functions.sh
|
||||
|
||||
# The mtd partition 'ubi' and 'rootfs_1' on NAND flash are os-image
|
||||
# partitions. These partitions are called as "Bank1/Bank2" in U-Boot
|
||||
# on WXR-2533DHP, and they are checked conditions when booting.
|
||||
# Then, U-Boot checks kernel and rootfs volumes in ubi, but U-Boot
|
||||
# needs "ubi_rootfs" as rootfs volume name. And, U-Boot checks the
|
||||
# checksum at the end of rootfs (ubi_rootfs).
|
||||
# When U-Boot writes os-image into the Bank, only kernel, rootfs
|
||||
# (ubi_rootfs) and rootfs_data (ubi_rootfs_data) volumes are wrote
|
||||
# into the Bank. (not full ubi image)
|
||||
#
|
||||
# == U-Boot Behaviors ==
|
||||
# - Bank1/Bank2 images are good, images are different
|
||||
# -> writes os-image to Bank1 from Bank2
|
||||
# (this behavior is used to firmware upgrade in stock firmware)
|
||||
# - Bank1 image is broken (or checksum error)
|
||||
# -> writes os-image to Bank1 from Bank2
|
||||
# - Bank2 image is broken (or checksum error)
|
||||
# -> writes os-image to Bank2 from Bank1
|
||||
# - Bank1/Bank2 images are broken (or checksum error)
|
||||
# -> start tftp
|
||||
CI_BUF_UBIPART="ubi"
|
||||
CI_BUF_UBIPART2="rootfs_1"
|
||||
KERN_VOLNAME="kernel"
|
||||
|
||||
buffalo_upgrade_prepare_ubi() {
|
||||
local rootfs_length="$1"
|
||||
|
||||
# search first ubi partition
|
||||
local mtdnum="$( find_mtd_index "$CI_BUF_UBIPART" )"
|
||||
if [ ! "$mtdnum" ]; then
|
||||
echo "cannot find first ubi mtd partition $CI_BUF_UBIPART"
|
||||
return 1
|
||||
fi
|
||||
|
||||
# search second ubi partition
|
||||
local mtdnum2="$( find_mtd_index "$CI_BUF_UBIPART2" )"
|
||||
if [ ! "$mtdnum2" ]; then
|
||||
echo "cannot find second ubi mtd partition $CI_BUF_UBIPART2"
|
||||
fi
|
||||
|
||||
local ubidev="$( nand_find_ubi "$CI_BUF_UBIPART" )"
|
||||
if [ ! "$ubidev" ]; then
|
||||
ubiattach -m "$mtdnum"
|
||||
sync
|
||||
ubidev="$( nand_find_ubi "$CI_BUF_UBIPART" )"
|
||||
fi
|
||||
|
||||
local ubidev2="$( nand_find_ubi "$CI_BUF_UBIPART2" )"
|
||||
if [ ! "$ubidev2" ] && [ -n "$mtdnum2" ]; then
|
||||
ubiattach -m "$mtdnum2"
|
||||
sync
|
||||
ubidev2="$( nand_find_ubi "$CI_BUF_UBIPART2" )"
|
||||
fi
|
||||
|
||||
if [ ! "$ubidev" ]; then
|
||||
ubiformat /dev/mtd$mtdnum -y
|
||||
ubiattach -m "$mtdnum"
|
||||
sync
|
||||
ubidev="$( nand_find_ubi "$CI_BUF_UBIPART" )"
|
||||
fi
|
||||
|
||||
local kern_ubivol="$( nand_find_volume $ubidev $KERN_VOLNAME )"
|
||||
local root_ubivol="$( nand_find_volume $ubidev ubi_rootfs )"
|
||||
local data_ubivol="$( nand_find_volume $ubidev rootfs_data )"
|
||||
# Buffalo volumes
|
||||
local buf_data_ubivol="$( nand_find_volume $ubidev ubi_rootfs_data )"
|
||||
local buf_kern2_ubivol="$( nand_find_volume $ubidev2 $KERN_VOLNAME )"
|
||||
|
||||
# remove ubiblock device of rootfs
|
||||
local root_ubiblk="ubiblock${root_ubivol:3}"
|
||||
if [ "$root_ubivol" -a -e "/dev/$root_ubiblk" ]; then
|
||||
echo "removing $root_ubiblk"
|
||||
if ! ubiblock -r /dev/$root_ubivol; then
|
||||
echo "cannot remove $root_ubiblk"
|
||||
return 1;
|
||||
fi
|
||||
fi
|
||||
|
||||
# kill volumes
|
||||
[ "$kern_ubivol" ] && ubirmvol /dev/$ubidev -N $KERN_VOLNAME || true
|
||||
[ "$root_ubivol" ] && ubirmvol /dev/$ubidev -N ubi_rootfs || true
|
||||
[ "$data_ubivol" ] && ubirmvol /dev/$ubidev -N rootfs_data || true
|
||||
[ "$buf_data_ubivol" ] && ubirmvol /dev/$ubidev -N ubi_rootfs_data || true
|
||||
|
||||
if ! ubimkvol /dev/$ubidev -N $KERN_VOLNAME -s $kernel_length; then
|
||||
echo "cannot create kernel volume"
|
||||
return 1;
|
||||
fi
|
||||
|
||||
if ! ubimkvol /dev/$ubidev -N ubi_rootfs -s $rootfs_length; then
|
||||
echo "cannot create rootfs volume"
|
||||
return 1;
|
||||
fi
|
||||
|
||||
if ! ubimkvol /dev/$ubidev -N rootfs_data -m; then
|
||||
echo "cannot initialize rootfs_data volume"
|
||||
return 1
|
||||
fi
|
||||
|
||||
# remove kernel volume from second ubi partition for U-Boot
|
||||
# U-Boot writes os-image into Bank2 from Bank1
|
||||
[ "$buf_kern2_ubivol" ] && ubirmvol /dev/$ubidev2 -N $KERN_VOLNAME || true
|
||||
|
||||
sync
|
||||
return 0
|
||||
}
|
||||
|
||||
buffalo_do_upgrade() {
|
||||
local tar_file="$1"
|
||||
local kernel_mtd="$(find_mtd_index $CI_BUF_UBIPART)"
|
||||
|
||||
local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$')
|
||||
board_dir=${board_dir%/}
|
||||
|
||||
local kernel_length=`(tar xf $tar_file ${board_dir}/kernel -O | wc -c) 2> /dev/null`
|
||||
local rootfs_length=`(tar xf $tar_file ${board_dir}/root -O | wc -c) 2> /dev/null`
|
||||
|
||||
local rootfs_type="$(identify_tar "$tar_file" ${board_dir}/root)"
|
||||
|
||||
buffalo_upgrade_prepare_ubi "$rootfs_length" || exit 1
|
||||
|
||||
local ubidev="$( nand_find_ubi "$CI_BUF_UBIPART" )"
|
||||
local kern_ubivol="$(nand_find_volume $ubidev $KERN_VOLNAME)"
|
||||
tar xf $tar_file ${board_dir}/kernel -O | \
|
||||
ubiupdatevol /dev/$kern_ubivol -s $kernel_length -
|
||||
|
||||
local root_ubivol="$(nand_find_volume $ubidev ubi_rootfs)"
|
||||
tar xf $tar_file ${board_dir}/root -O | \
|
||||
ubiupdatevol /dev/$root_ubivol -s $rootfs_length -
|
||||
|
||||
CI_UBIPART="$CI_BUF_UBIPART"
|
||||
nand_do_upgrade_success
|
||||
}
|
||||
@ -10,12 +10,16 @@ platform_check_image() {
|
||||
|
||||
platform_do_upgrade() {
|
||||
case "$(board_name)" in
|
||||
buffalo,wxr-2533dhp)
|
||||
buffalo_do_upgrade "$ARGV"
|
||||
;;
|
||||
compex,wpq864|\
|
||||
netgear,d7800 |\
|
||||
netgear,r7500 |\
|
||||
netgear,r7500v2 |\
|
||||
netgear,r7800 |\
|
||||
qcom,ipq8064-ap148 |\
|
||||
qcom,ipq8064-ap161 |\
|
||||
zyxel,nbg6817)
|
||||
nand_do_upgrade "$ARGV"
|
||||
;;
|
||||
|
||||
@ -0,0 +1,277 @@
|
||||
#include "qcom-ipq8064-v1.0.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Qualcomm IPQ8064/AP161";
|
||||
compatible = "qcom,ipq8064-ap161", "qcom,ipq8064";
|
||||
|
||||
memory@0 {
|
||||
reg = <0x42000000 0x1e000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
rsvd@41200000 {
|
||||
reg = <0x41200000 0x300000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &gsbi4_serial;
|
||||
mdio-gpio0 = &mdio0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
linux,stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
soc {
|
||||
pinmux@800000 {
|
||||
i2c4_pins: i2c4_pinmux {
|
||||
pins = "gpio12", "gpio13";
|
||||
function = "gsbi4";
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
spi_pins: spi_pins {
|
||||
mux {
|
||||
pins = "gpio18", "gpio19", "gpio21";
|
||||
function = "gsbi5";
|
||||
drive-strength = <10>;
|
||||
bias-none;
|
||||
};
|
||||
};
|
||||
nand_pins: nand_pins {
|
||||
mux {
|
||||
pins = "gpio34", "gpio35", "gpio36",
|
||||
"gpio37", "gpio38", "gpio39",
|
||||
"gpio40", "gpio41", "gpio42",
|
||||
"gpio43", "gpio44", "gpio45",
|
||||
"gpio46", "gpio47";
|
||||
function = "nand";
|
||||
drive-strength = <10>;
|
||||
bias-disable;
|
||||
};
|
||||
pullups {
|
||||
pins = "gpio39";
|
||||
bias-pull-up;
|
||||
};
|
||||
hold {
|
||||
pins = "gpio40", "gpio41", "gpio42",
|
||||
"gpio43", "gpio44", "gpio45",
|
||||
"gpio46", "gpio47";
|
||||
bias-bus-hold;
|
||||
};
|
||||
};
|
||||
|
||||
mdio0_pins: mdio0_pins {
|
||||
mux {
|
||||
pins = "gpio0", "gpio1";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
rgmii2_pins: rgmii2_pins {
|
||||
mux {
|
||||
pins = "gpio2", "gpio27", "gpio28",
|
||||
"gpio29", "gpio30", "gpio31",
|
||||
"gpio32", "gpio51", "gpio52",
|
||||
"gpio59", "gpio60", "gpio61",
|
||||
"gpio62" , "gpio66";
|
||||
function = "rgmii2";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gsbi@16300000 {
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
status = "ok";
|
||||
serial@16340000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
/*
|
||||
* The i2c device on gsbi4 should not be enabled.
|
||||
* On ipq806x designs gsbi4 i2c is meant for exclusive
|
||||
* RPM usage. Turning this on in kernel manifests as
|
||||
* i2c failure for the RPM.
|
||||
*/
|
||||
};
|
||||
|
||||
gsbi5: gsbi@1a200000 {
|
||||
qcom,mode = <GSBI_PROT_SPI>;
|
||||
status = "ok";
|
||||
|
||||
spi4: spi@1a280000 {
|
||||
status = "ok";
|
||||
spi-max-frequency = <50000000>;
|
||||
|
||||
pinctrl-0 = <&spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs-gpios = <&qcom_pinmux 20 0>;
|
||||
|
||||
flash: m25p80@0 {
|
||||
compatible = "s25fl256s1";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
|
||||
partitions {
|
||||
compatible = "qcom,smem";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
sata-phy@1b400000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
sata@29000000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@100f8800 { /* USB3 port 1 HS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@100f8830 { /* USB3 port 1 SS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@110f8800 { /* USB3 port 0 HS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@110f8830 { /* USB3 port 0 SS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb30@0 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb30@1 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
pcie0: pci@1b500000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
pcie1: pci@1b700000 {
|
||||
status = "ok";
|
||||
force_gen1 = <1>;
|
||||
};
|
||||
|
||||
pcie2: pci@1b900000 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
nand@1ac00000 {
|
||||
status = "ok";
|
||||
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs0 {
|
||||
reg = <0>;
|
||||
compatible = "qcom,nandcs";
|
||||
|
||||
nand-ecc-strength = <4>;
|
||||
nand-bus-width = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "qcom,smem";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
mdio0: mdio {
|
||||
compatible = "virtual,mdio-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
|
||||
pinctrl-0 = <&mdio0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
qca,ar8327-initvals = <
|
||||
0x00004 0x7600000 /* PAD0_MODE */
|
||||
0x00008 0x1000000 /* PAD5_MODE */
|
||||
0x0000c 0x20080 /* PAD6_MODE */
|
||||
0x000e4 0x6a545 /* MAC_POWER_SEL */
|
||||
0x000e0 0xc74164de /* SGMII_CTRL */
|
||||
0x0007c 0x4e /* PORT0_STATUS */
|
||||
0x00094 0x4e /* PORT6_STATUS */
|
||||
>;
|
||||
};
|
||||
|
||||
phy4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
qca,phy-rgmii-en;
|
||||
qca,txclk-delay-en;
|
||||
qca,rxclk-delay-en;
|
||||
};
|
||||
|
||||
phy3: ethernet-phy@3 {
|
||||
device_type = "ethernet-phy";
|
||||
reg = <3>;
|
||||
};
|
||||
};
|
||||
|
||||
gmac0: ethernet@37000000 {
|
||||
status = "ok";
|
||||
phy-mode = "rgmii";
|
||||
qcom,id = <0>;
|
||||
|
||||
pinctrl-0 = <&rgmii2_pins>;
|
||||
pinctrl-names = "default";
|
||||
mdiobus = <&mdio0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: ethernet@37200000 {
|
||||
status = "ok";
|
||||
phy-mode = "rgmii";
|
||||
qcom,id = <1>;
|
||||
mdiobus = <&mdio0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
gmac2: ethernet@37400000 {
|
||||
status = "ok";
|
||||
phy-mode = "sgmii";
|
||||
qcom,id = <2>;
|
||||
mdiobus = <&mdio0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&adm_dma {
|
||||
status = "ok";
|
||||
};
|
||||
@ -26,7 +26,7 @@
|
||||
mdio-gpio0 = &mdio0;
|
||||
|
||||
led-boot = &power_green;
|
||||
led-failsafe = &power_green;
|
||||
led-failsafe = &power_red;
|
||||
led-running = &power_green;
|
||||
led-upgrade = &power_green;
|
||||
};
|
||||
@ -36,256 +36,6 @@
|
||||
};
|
||||
|
||||
soc {
|
||||
pinmux@800000 {
|
||||
button_pins: button_pins {
|
||||
mux {
|
||||
pins = "gpio16", "gpio54", "gpio24", "gpio25";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
i2c4_pins: i2c4_pinmux {
|
||||
mux {
|
||||
pins = "gpio12", "gpio13";
|
||||
function = "gsbi4";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
led_pins: led_pins {
|
||||
mux {
|
||||
pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio14",
|
||||
"gpio15", "gpio55", "gpio56", "gpio57", "gpio58",
|
||||
"gpio64", "gpio65";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
spi_pins: spi_pins {
|
||||
mux {
|
||||
pins = "gpio18", "gpio19", "gpio21";
|
||||
function = "gsbi5";
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
data {
|
||||
pins = "gpio18", "gpio19";
|
||||
drive-strength = <10>;
|
||||
};
|
||||
|
||||
cs {
|
||||
pins = "gpio20";
|
||||
drive-strength = <10>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
clk {
|
||||
pins = "gpio21";
|
||||
drive-strength = <12>;
|
||||
};
|
||||
};
|
||||
|
||||
mdio0_pins: mdio0_pins {
|
||||
mux {
|
||||
pins = "gpio0", "gpio1";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
rgmii2_pins: rgmii2_pins {
|
||||
mux {
|
||||
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
|
||||
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
|
||||
function = "rgmii2";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
usb_pwr_en_pins: usb_pwr_en_pins {
|
||||
mux {
|
||||
pins = "gpio22";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-down;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gsbi@16300000 {
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
status = "ok";
|
||||
serial@16340000 {
|
||||
status = "ok";
|
||||
};
|
||||
/*
|
||||
* The i2c device on gsbi4 should not be enabled.
|
||||
* On ipq806x designs gsbi4 i2c is meant for exclusive
|
||||
* RPM usage. Turning this on in kernel manifests as
|
||||
* i2c failure for the RPM.
|
||||
*/
|
||||
};
|
||||
|
||||
gsbi5: gsbi@1a200000 {
|
||||
qcom,mode = <GSBI_PROT_SPI>;
|
||||
status = "ok";
|
||||
|
||||
spi4: spi@1a280000 {
|
||||
status = "ok";
|
||||
|
||||
pinctrl-0 = <&spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash: m25p80@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
|
||||
SBL1@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
MIBIB@20000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x20000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SBL2@40000 {
|
||||
label = "SBL2";
|
||||
reg = <0x40000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SBL3@80000 {
|
||||
label = "SBL3";
|
||||
reg = <0x80000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
DDRCONFIG@100000 {
|
||||
label = "DDRCONFIG";
|
||||
reg = <0x100000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SSD@110000 {
|
||||
label = "SSD";
|
||||
reg = <0x110000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
TZ@120000 {
|
||||
label = "TZ";
|
||||
reg = <0x120000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
RPM@1a0000 {
|
||||
label = "RPM";
|
||||
reg = <0x1a0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBL@220000 {
|
||||
label = "APPSBL";
|
||||
reg = <0x220000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBLENV@2a0000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0x2a0000 0x10000>;
|
||||
};
|
||||
|
||||
PRODUCTDATA: PRODUCTDATA@2b0000 {
|
||||
label = "PRODUCTDATA";
|
||||
reg = <0x2b0000 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
ART@2e0000 {
|
||||
label = "ART";
|
||||
reg = <0x2e0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
TP@320000 {
|
||||
label = "TP";
|
||||
reg = <0x320000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
TINY@360000 {
|
||||
label = "TINY";
|
||||
reg = <0x360000 0x500000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
firmware@860000 {
|
||||
label = "firmware";
|
||||
reg = <0x860000 0x17a0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
phy@100f8800 { /* USB3 port 1 HS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@100f8830 { /* USB3 port 1 SS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@110f8800 { /* USB3 port 0 HS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
phy@110f8830 { /* USB3 port 0 SS phy */
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
usb30@0 {
|
||||
status = "ok";
|
||||
|
||||
pinctrl-0 = <&usb_pwr_en_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
usb30@1 {
|
||||
status = "ok";
|
||||
};
|
||||
|
||||
pcie0: pci@1b500000 {
|
||||
status = "ok";
|
||||
reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&pcie0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
pcie1: pci@1b700000 {
|
||||
status = "ok";
|
||||
reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&pcie1_pins>;
|
||||
pinctrl-names = "default";
|
||||
force_gen1 = <1>;
|
||||
};
|
||||
|
||||
mdio0: mdio {
|
||||
compatible = "virtual,mdio-gpio";
|
||||
#address-cells = <1>;
|
||||
@ -294,52 +44,22 @@
|
||||
pinctrl-0 = <&mdio0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
qca,ar8327-initvals = <
|
||||
0x00004 0x7600000 /* PAD0_MODE */
|
||||
0x00008 0x1000000 /* PAD5_MODE */
|
||||
0x0000c 0x80 /* PAD6_MODE */
|
||||
0x000e4 0x6a545 /* MAC_POWER_SEL */
|
||||
0x00004 0x06000000 /* PAD0_MODE */
|
||||
0x0000c 0x00080080 /* PAD6_MODE */
|
||||
0x000e4 0x0006a545 /* MAC_POWER_SEL */
|
||||
0x000e0 0xc74164de /* SGMII_CTRL */
|
||||
0x0007c 0x4e /* PORT0_STATUS */
|
||||
0x00094 0x4e /* PORT6_STATUS */
|
||||
0x0007c 0x0000004e /* PORT0_STATUS */
|
||||
0x00094 0x0000004e /* PORT6_STATUS */
|
||||
>;
|
||||
};
|
||||
|
||||
phy4: ethernet-phy@4 {
|
||||
ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: ethernet@37200000 {
|
||||
status = "ok";
|
||||
phy-mode = "rgmii";
|
||||
qcom,id = <1>;
|
||||
|
||||
pinctrl-0 = <&rgmii2_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
mtd-mac-address = <&PRODUCTDATA 6>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
gmac2: ethernet@37400000 {
|
||||
status = "ok";
|
||||
phy-mode = "sgmii";
|
||||
qcom,id = <2>;
|
||||
|
||||
mtd-mac-address = <&PRODUCTDATA 0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
@ -384,7 +104,7 @@
|
||||
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
power_red {
|
||||
power_red: power_red {
|
||||
label = "wg2600hp:red:power";
|
||||
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
@ -442,5 +162,281 @@
|
||||
};
|
||||
|
||||
&adm_dma {
|
||||
status = "ok";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "rgmii";
|
||||
qcom,id = <1>;
|
||||
|
||||
pinctrl-0 = <&rgmii2_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
mtd-mac-address = <&PRODUCTDATA 6>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "sgmii";
|
||||
qcom,id = <2>;
|
||||
|
||||
mtd-mac-address = <&PRODUCTDATA 0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&gsbi4 {
|
||||
status = "okay";
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
};
|
||||
|
||||
&gsbi4_serial {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gsbi5 {
|
||||
status = "okay";
|
||||
|
||||
qcom,mode = <GSBI_PROT_SPI>;
|
||||
|
||||
spi@1a280000 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
SBL1@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
MIBIB@20000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x20000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SBL2@40000 {
|
||||
label = "SBL2";
|
||||
reg = <0x40000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SBL3@80000 {
|
||||
label = "SBL3";
|
||||
reg = <0x80000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
DDRCONFIG@100000 {
|
||||
label = "DDRCONFIG";
|
||||
reg = <0x100000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SSD@110000 {
|
||||
label = "SSD";
|
||||
reg = <0x110000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
TZ@120000 {
|
||||
label = "TZ";
|
||||
reg = <0x120000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
RPM@1a0000 {
|
||||
label = "RPM";
|
||||
reg = <0x1a0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBL@220000 {
|
||||
label = "APPSBL";
|
||||
reg = <0x220000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBLENV@2a0000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0x2a0000 0x10000>;
|
||||
};
|
||||
|
||||
PRODUCTDATA: PRODUCTDATA@2b0000 {
|
||||
label = "PRODUCTDATA";
|
||||
reg = <0x2b0000 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
ART@2e0000 {
|
||||
label = "ART";
|
||||
reg = <0x2e0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
TP@320000 {
|
||||
label = "TP";
|
||||
reg = <0x320000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
TINY@360000 {
|
||||
label = "TINY";
|
||||
reg = <0x360000 0x500000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
firmware@860000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x860000 0x17a0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&hs_phy_0 { /* USB3 port 0 HS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ss_phy_0 { /* USB3 port 0 SS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hs_phy_1 { /* USB3 port 1 HS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ss_phy_1 { /* USB3 port 1 SS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_0 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&usb_pwr_en_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&usb3_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
force_gen1 = <1>;
|
||||
};
|
||||
|
||||
&qcom_pinmux {
|
||||
button_pins: button_pins {
|
||||
mux {
|
||||
pins = "gpio16", "gpio54", "gpio24", "gpio25";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
i2c4_pins: i2c4_pinmux {
|
||||
mux {
|
||||
pins = "gpio12", "gpio13";
|
||||
function = "gsbi4";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
led_pins: led_pins {
|
||||
mux {
|
||||
pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio14",
|
||||
"gpio15", "gpio55", "gpio56", "gpio57", "gpio58",
|
||||
"gpio64", "gpio65";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
spi_pins: spi_pins {
|
||||
mux {
|
||||
pins = "gpio18", "gpio19", "gpio21";
|
||||
function = "gsbi5";
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
data {
|
||||
pins = "gpio18", "gpio19";
|
||||
drive-strength = <10>;
|
||||
};
|
||||
|
||||
cs {
|
||||
pins = "gpio20";
|
||||
drive-strength = <10>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
clk {
|
||||
pins = "gpio21";
|
||||
drive-strength = <12>;
|
||||
};
|
||||
};
|
||||
|
||||
mdio0_pins: mdio0_pins {
|
||||
mux {
|
||||
pins = "gpio0", "gpio1";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
rgmii2_pins: rgmii2_pins {
|
||||
mux {
|
||||
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
|
||||
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
|
||||
function = "rgmii2";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
usb_pwr_en_pins: usb_pwr_en_pins {
|
||||
mux {
|
||||
pins = "gpio22";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-down;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -0,0 +1,535 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
#include "qcom-ipq8064-v2.0.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Buffalo WXR-2533DHP";
|
||||
compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064";
|
||||
|
||||
memory@42000000 {
|
||||
reg = <0x42000000 0x1e000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
rsvd@41200000 {
|
||||
reg = <0x41200000 0x300000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &gsbi4_serial;
|
||||
|
||||
led-boot = &power;
|
||||
led-failsafe = &diag;
|
||||
led-running = &power;
|
||||
led-upgrade = &power;
|
||||
};
|
||||
|
||||
chosen {
|
||||
/* use "ubi_rootfs" volume in "ubi" partition as rootfs */
|
||||
bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs";
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
soc {
|
||||
nand@1ac00000 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs@0 {
|
||||
reg = <0>;
|
||||
compatible = "qcom,nandcs";
|
||||
|
||||
nand-ecc-strength = <4>;
|
||||
nand-bus-width = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
ubi@0 {
|
||||
label = "ubi";
|
||||
reg = <0x0000000 0x4000000>;
|
||||
};
|
||||
|
||||
rootfs_1@4000000 {
|
||||
label = "rootfs_1";
|
||||
reg = <0x4000000 0x4000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
mdio {
|
||||
compatible = "virtual,mdio-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
|
||||
<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&mdio0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
qca,ar8327-initvals = <
|
||||
0x00004 0x07600000 /* PAD0_MODE */
|
||||
0x00008 0x01000000 /* PAD5_MODE */
|
||||
0x0000c 0x00000080 /* PAD6_MODE */
|
||||
0x00050 0xcc35cc35 /* LED_CTRL0 */
|
||||
0x00054 0xca35ca35 /* LED_CTRL1 */
|
||||
0x00058 0xc935c935 /* LED_CTRL2 */
|
||||
0x0005c 0x03ffff00 /* LED_CTRL3 */
|
||||
0x000e4 0x0006a545 /* MAC_POWER_SEL */
|
||||
0x000e0 0xc74164de /* SGMII_CTRL */
|
||||
0x0007c 0x0000007e /* PORT0_STATUS */
|
||||
0x00094 0x0000007e /* PORT6_STATUS */
|
||||
>;
|
||||
};
|
||||
|
||||
ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&led_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
usb {
|
||||
label = "wxr-2533dhp:green:usb";
|
||||
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "usbport";
|
||||
trigger-sources = <&hub_port0 &hub_port1>;
|
||||
};
|
||||
|
||||
guestport {
|
||||
label = "wxr-2533dhp:green:guestport";
|
||||
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
diag: diag {
|
||||
label = "wxr-2533dhp:orange:diag";
|
||||
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
internet_orange {
|
||||
label = "wxr-2533dhp:orange:internet";
|
||||
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
internet_white {
|
||||
label = "wxr-2533dhp:white:internet";
|
||||
gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wireless_orange {
|
||||
label = "wxr-2533dhp:orange:wireless";
|
||||
gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wireless_white {
|
||||
label = "wxr-2533dhp:white:wireless";
|
||||
gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
router_orange {
|
||||
label = "wxr-2533dhp:orange:router";
|
||||
gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
router_white {
|
||||
label = "wxr-2533dhp:white:router";
|
||||
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power: power {
|
||||
label = "wxr-2533dhp:white:power";
|
||||
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
power {
|
||||
label = "power";
|
||||
gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_POWER>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
eject {
|
||||
label = "eject";
|
||||
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_EJECTCD>;
|
||||
};
|
||||
|
||||
guest {
|
||||
label = "guest";
|
||||
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
};
|
||||
|
||||
ap {
|
||||
label = "ap";
|
||||
gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
router {
|
||||
label = "router";
|
||||
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
auto {
|
||||
label = "auto";
|
||||
gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&adm_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "rgmii";
|
||||
qcom,id = <1>;
|
||||
|
||||
pinctrl-0 = <&rgmii2_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
mtd-mac-address = <&ART 6>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
status = "ok";
|
||||
|
||||
phy-mode = "sgmii";
|
||||
qcom,id = <2>;
|
||||
|
||||
mtd-mac-address = <&ART 0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&gsbi4 {
|
||||
status = "okay";
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
};
|
||||
|
||||
&gsbi4_serial {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&uart0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&gsbi5 {
|
||||
status = "okay";
|
||||
qcom,mode = <GSBI_PROT_SPI>;
|
||||
|
||||
spi@1a280000 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
SBL1@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x0 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
MIBIB@10000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x10000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SBL2@30000 {
|
||||
label = "SBL2";
|
||||
reg = <0x30000 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SBL3@60000 {
|
||||
label = "SBL3";
|
||||
reg = <0x60000 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
DDRCONFIG@90000 {
|
||||
label = "DDRCONFIG";
|
||||
reg = <0x90000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SSD@a0000 {
|
||||
label = "SSD";
|
||||
reg = <0xa0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
TZ@b0000 {
|
||||
label = "TZ";
|
||||
reg = <0xb0000 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
RPM@e0000 {
|
||||
label = "RPM";
|
||||
reg = <0xe0000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBL@100000 {
|
||||
label = "APPSBL";
|
||||
reg = <0x100000 0x70000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBLENV@170000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0x170000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
ART: ART@180000 {
|
||||
label = "ART";
|
||||
reg = <0x180000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
BOOTCONFIG@1c0000 {
|
||||
label = "BOOTCONFIG";
|
||||
reg = <0x1c0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBL_1@1d0000 {
|
||||
label = "APPSBL_1";
|
||||
reg = <0x1d0000 0x70000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&hs_phy_0 { /* USB3 port 0 HS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ss_phy_0 { /* USB3 port 0 SS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hs_phy_1 { /* USB3 port 1 HS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ss_phy_1 { /* USB3 port 1 SS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_0 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&usb_pwr_en_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&usb3_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dwc3_0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
hub_port0: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&dwc3_1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
hub_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
force_gen1 = <1>;
|
||||
};
|
||||
|
||||
&qcom_pinmux {
|
||||
button_pins: button_pins {
|
||||
mux {
|
||||
pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57",
|
||||
"gpio58", "gpio64", "gpio65";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
led_pins: led_pins {
|
||||
mux {
|
||||
pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22",
|
||||
"gpio23", "gpio24", "gpio25", "gpio26", "gpio53";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
uart0_pins: uart0_pins {
|
||||
mux {
|
||||
pins = "gpio10", "gpio11";
|
||||
function = "gsbi4";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_pins: spi_pins {
|
||||
mux {
|
||||
pins = "gpio18", "gpio19", "gpio21";
|
||||
function = "gsbi5";
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
data {
|
||||
pins = "gpio18", "gpio19";
|
||||
drive-strength = <10>;
|
||||
};
|
||||
|
||||
cs{
|
||||
pins = "gpio20";
|
||||
drive-strength = <10>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
clk {
|
||||
pins = "gpio21";
|
||||
drive-strength = <12>;
|
||||
};
|
||||
};
|
||||
|
||||
mdio0_pins: mdio0_pins {
|
||||
mux {
|
||||
pins = "gpio0", "gpio1";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
nand_pins: nand_pins {
|
||||
mux {
|
||||
pins = "gpio34", "gpio35", "gpio36",
|
||||
"gpio37", "gpio38", "gpio39",
|
||||
"gpio40", "gpio41", "gpio42",
|
||||
"gpio43", "gpio44", "gpio45",
|
||||
"gpio46", "gpio47";
|
||||
function = "nand";
|
||||
drive-strength = <10>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
pullups {
|
||||
pins = "gpio39";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
hold {
|
||||
pins = "gpio40", "gpio41", "gpio42",
|
||||
"gpio43", "gpio44", "gpio45",
|
||||
"gpio46", "gpio47";
|
||||
bias-bus-hold;
|
||||
};
|
||||
};
|
||||
|
||||
rgmii2_pins: rgmii2_pins {
|
||||
mux {
|
||||
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
|
||||
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
|
||||
function = "rgmii2";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
usb_pwr_en_pins: usb_pwr_en_pins {
|
||||
mux{
|
||||
pins = "gpio68";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -972,7 +972,7 @@
|
||||
|
||||
status = "disabled";
|
||||
|
||||
dwc3@11000000 {
|
||||
dwc3_0: dwc3@11000000 {
|
||||
compatible = "snps,dwc3";
|
||||
reg = <0x11000000 0xcd00>;
|
||||
interrupts = <0 110 0x4>;
|
||||
@ -997,7 +997,7 @@
|
||||
|
||||
status = "disabled";
|
||||
|
||||
dwc3@10000000 {
|
||||
dwc3_1: dwc3@10000000 {
|
||||
compatible = "snps,dwc3";
|
||||
reg = <0x10000000 0xcd00>;
|
||||
interrupts = <0 205 0x4>;
|
||||
|
||||
@ -3,6 +3,13 @@
|
||||
include $(TOPDIR)/rules.mk
|
||||
include $(INCLUDE_DIR)/image.mk
|
||||
|
||||
define Build/buffalo-rootfs-cksum
|
||||
( \
|
||||
echo -ne "\x$$(od -A n -t u1 $@ | tr -s ' ' '\n' | \
|
||||
$(STAGING_DIR_HOST)/bin/awk '{s+=$$0}END{printf "%x", 255-s%256}')"; \
|
||||
) >> $@
|
||||
endef
|
||||
|
||||
define Device/Default
|
||||
PROFILES := Default
|
||||
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
|
||||
@ -67,13 +74,26 @@ define Device/ZyXELImage
|
||||
KERNEL_SUFFIX := -uImage
|
||||
KERNEL = kernel-bin | append-dtb | uImage none | pad-to $${KERNEL_SIZE}
|
||||
KERNEL_NAME := zImage
|
||||
IMAGES := factory.bin sysupgrade.bin mmcblk0p5-rootfs.bin mmcblk0p4-kernel.bin
|
||||
IMAGES := factory.bin sysupgrade.bin
|
||||
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | zyxel-ras-image separate-kernel
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
IMAGE/mmcblk0p5-rootfs.bin := append-rootfs | pad-rootfs | pad-to $$$${BLOCKSIZE}
|
||||
IMAGE/mmcblk0p4-kernel.bin := append-kernel
|
||||
endef
|
||||
|
||||
define Device/buffalo_wxr-2533dhp
|
||||
$(call Device/LegacyImage)
|
||||
DEVICE_DTS := qcom-ipq8064-wxr-2533dhp
|
||||
DEVICE_TITLE := Buffalo WXR-2533DHP
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 65536k
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := append-rootfs | buffalo-rootfs-cksum | \
|
||||
sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += buffalo_wxr-2533dhp
|
||||
|
||||
define Device/compex_wpq864
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
@ -98,7 +118,7 @@ define Device/linksys_ea8500
|
||||
IMAGES := factory.bin sysupgrade.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-ubi
|
||||
DEVICE_TITLE := Linksys EA8500
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += linksys_ea8500
|
||||
|
||||
@ -110,7 +130,7 @@ define Device/nec_wg2600hp
|
||||
DEVICE_TITLE := NEC Aterm WG2600HP
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += nec_wg2600hp
|
||||
|
||||
@ -125,7 +145,7 @@ define Device/netgear_d7800
|
||||
BOARD_NAME := d7800
|
||||
SUPPORTED_DEVICES += d7800
|
||||
DEVICE_TITLE := Netgear Nighthawk X4 D7800
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += netgear_d7800
|
||||
|
||||
@ -140,7 +160,7 @@ define Device/netgear_r7500
|
||||
BOARD_NAME := r7500
|
||||
SUPPORTED_DEVICES += r7500
|
||||
DEVICE_TITLE := Netgear Nighthawk X4 R7500
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca988x
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct
|
||||
endef
|
||||
TARGET_DEVICES += netgear_r7500
|
||||
|
||||
@ -155,7 +175,7 @@ define Device/netgear_r7500v2
|
||||
BOARD_NAME := r7500v2
|
||||
SUPPORTED_DEVICES += r7500v2
|
||||
DEVICE_TITLE := Netgear Nighthawk X4 R7500v2
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0 ath10k-firmware-qca988x
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct ath10k-firmware-qca988x-ct
|
||||
endef
|
||||
TARGET_DEVICES += netgear_r7500v2
|
||||
|
||||
@ -170,7 +190,7 @@ define Device/netgear_r7800
|
||||
BOARD_NAME := r7800
|
||||
SUPPORTED_DEVICES += r7800
|
||||
DEVICE_TITLE := Netgear Nighthawk X4S R7800
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct
|
||||
endef
|
||||
TARGET_DEVICES += netgear_r7800
|
||||
|
||||
@ -184,7 +204,7 @@ define Device/qcom_ipq8064-ap148
|
||||
BOARD_NAME := ap148
|
||||
SUPPORTED_DEVICES += ap148
|
||||
DEVICE_TITLE := Qualcomm AP148
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += qcom_ipq8064-ap148
|
||||
|
||||
@ -197,17 +217,30 @@ define Device/qcom_ipq8064-ap148-legacy
|
||||
BOARD_NAME := ap148
|
||||
SUPPORTED_DEVICES := qcom,ipq8064-ap148 ap148
|
||||
DEVICE_TITLE := Qualcomm AP148 (legacy)
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += qcom_ipq8064-ap148-legacy
|
||||
|
||||
define Device/qcom_ipq8064-ap161
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_DTS := qcom-ipq8064-ap161
|
||||
KERNEL_INSTALL := 1
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
BOARD_NAME := ap161
|
||||
DEVICE_TITLE := Qualcomm AP161
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += qcom_ipq8064-ap161
|
||||
|
||||
define Device/qcom_ipq8064-db149
|
||||
$(call Device/FitImage)
|
||||
DEVICE_DTS := qcom-ipq8064-db149
|
||||
KERNEL_INSTALL := 1
|
||||
BOARD_NAME := db149
|
||||
DEVICE_TITLE := Qualcomm DB149
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += qcom_ipq8064-db149
|
||||
|
||||
@ -220,7 +253,7 @@ define Device/tplink_c2600
|
||||
SUPPORTED_DEVICES += c2600
|
||||
TPLINK_BOARD_ID := C2600
|
||||
DEVICE_TITLE := TP-Link Archer C2600
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += tplink_c2600
|
||||
|
||||
@ -235,7 +268,7 @@ define Device/tplink_vr2600v
|
||||
BOARD_NAME := vr2600v
|
||||
SUPPORTED_DEVICES += vr2600v
|
||||
DEVICE_TITLE := TP-Link Archer VR2600v
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
|
||||
endef
|
||||
@ -251,7 +284,7 @@ define Device/zyxel_nbg6817
|
||||
RAS_VERSION := "V1.99(OWRT.9999)C0"
|
||||
SUPPORTED_DEVICES += nbg6817
|
||||
DEVICE_TITLE := ZyXEL NBG6817
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984 e2fsprogs kmod-fs-ext4 losetup
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs kmod-fs-ext4 losetup
|
||||
$(call Device/ZyXELImage)
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_nbg6817
|
||||
|
||||
@ -10,18 +10,20 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -699,6 +699,16 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -699,6 +699,18 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
qcom-ipq4019-ap.dk01.1-c1.dtb \
|
||||
qcom-ipq8064-ap148.dtb \
|
||||
+ qcom-ipq8064-c2600.dtb \
|
||||
+ qcom-ipq8064-d7800.dtb \
|
||||
+ qcom-ipq8064-db149.dtb \
|
||||
+ qcom-ipq8064-ap161.dtb \
|
||||
+ qcom-ipq8064-ea8500.dtb \
|
||||
+ qcom-ipq8064-r7500.dtb \
|
||||
+ qcom-ipq8064-r7500v2.dtb \
|
||||
+ qcom-ipq8064-wg2600hp.dtb \
|
||||
+ qcom-ipq8064-wpq864.dtb \
|
||||
+ qcom-ipq8064-wxr-2533dhp.dtb \
|
||||
+ qcom-ipq8065-nbg6817.dtb \
|
||||
+ qcom-ipq8065-r7800.dtb \
|
||||
qcom-msm8660-surf.dtb \
|
||||
|
||||
Loading…
Reference in New Issue
Block a user