filogic: add support for GL.iNet GL-MT6000 support

target/linux/generic/pending-5.15/731-net-phy-realtek-support-interrupt-of-RTL8221B.patch

@@ -0,0 +1,63 @@
+--- a/drivers/net/phy/realtek.c
++++ b/drivers/net/phy/realtek.c
+@@ -971,6 +971,51 @@ static int rtl8221b_config_init(struct p
+ 	return 0;
+ }
+ 
++static int rtl8221b_ack_interrupt(struct phy_device *phydev)
++{
++	int err;
++
++	err = phy_read_mmd(phydev, RTL8221B_MMD_PHY_CTRL, 0xa4d4);
++
++	return (err < 0) ? err : 0;
++}
++
++static int rtl8221b_config_intr(struct phy_device *phydev)
++{
++	int err;
++
++	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
++		err = rtl8221b_ack_interrupt(phydev);
++		if (err)
++			return err;
++
++		err = phy_write_mmd(phydev, RTL8221B_MMD_PHY_CTRL, 0xa4d2, 0x7ff);
++	} else {
++		err = phy_write_mmd(phydev, RTL8221B_MMD_PHY_CTRL, 0xa4d2, 0x0);
++		if (err)
++			return err;
++
++		err = rtl8221b_ack_interrupt(phydev);
++	}
++
++	return err;
++}
++
++static irqreturn_t rtl8221b_handle_interrupt(struct phy_device *phydev)
++{
++	int err;
++
++	err = rtl8221b_ack_interrupt(phydev);
++	if (err) {
++		phy_error(phydev);
++		return IRQ_NONE;
++	}
++
++	phy_trigger_machine(phydev);
++
++	return IRQ_HANDLED;
++}
++
+ static struct phy_driver realtek_drvs[] = {
+ 	{
+ 		PHY_ID_MATCH_EXACT(0x00008201),
+@@ -1119,6 +1164,8 @@ static struct phy_driver realtek_drvs[]
+ 		.get_features   = rtl822x_get_features,
+ 		.config_init    = rtl8221b_config_init,
+ 		.config_aneg    = rtl822x_config_aneg,
++		.config_intr	= rtl8221b_config_intr,
++		.handle_interrupt = rtl8221b_handle_interrupt,
+ 		.probe          = rtl822x_probe,
+ 		.read_status    = rtl822x_read_status,
+ 		.suspend        = genphy_suspend,

target/linux/generic/pending-6.1/741-net-phy-realtek-support-interrupt-of-RTL8221B.patch

@@ -0,0 +1,63 @@
+--- a/drivers/net/phy/realtek.c
++++ b/drivers/net/phy/realtek.c
+@@ -979,6 +979,51 @@ static int rtl8221b_config_init(struct p
+ 	return 0;
+ }
+ 
++static int rtl8221b_ack_interrupt(struct phy_device *phydev)
++{
++	int err;
++
++	err = phy_read_mmd(phydev, RTL8221B_MMD_PHY_CTRL, 0xa4d4);
++
++	return (err < 0) ? err : 0;
++}
++
++static int rtl8221b_config_intr(struct phy_device *phydev)
++{
++	int err;
++
++	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
++		err = rtl8221b_ack_interrupt(phydev);
++		if (err)
++			return err;
++
++		err = phy_write_mmd(phydev, RTL8221B_MMD_PHY_CTRL, 0xa4d2, 0x7ff);
++	} else {
++		err = phy_write_mmd(phydev, RTL8221B_MMD_PHY_CTRL, 0xa4d2, 0x0);
++		if (err)
++			return err;
++
++		err = rtl8221b_ack_interrupt(phydev);
++	}
++
++	return err;
++}
++
++static irqreturn_t rtl8221b_handle_interrupt(struct phy_device *phydev)
++{
++	int err;
++
++	err = rtl8221b_ack_interrupt(phydev);
++	if (err) {
++		phy_error(phydev);
++		return IRQ_NONE;
++	}
++
++	phy_trigger_machine(phydev);
++
++	return IRQ_HANDLED;
++}
++
+ static struct phy_driver realtek_drvs[] = {
+ 	{
+ 		PHY_ID_MATCH_EXACT(0x00008201),
+@@ -1139,6 +1184,8 @@ static struct phy_driver realtek_drvs[]
+ 		.get_features   = rtl822x_get_features,
+ 		.config_init    = rtl8221b_config_init,
+ 		.config_aneg    = rtl822x_config_aneg,
++		.config_intr	= rtl8221b_config_intr,
++		.handle_interrupt = rtl8221b_handle_interrupt,
+ 		.probe          = rtl822x_probe,
+ 		.read_status    = rtl822x_read_status,
+ 		.suspend        = genphy_suspend,

target/linux/mediatek/dts/mt7986a-glinet-gl-mt6000.dts

@@ -0,0 +1,306 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	model = "GL.iNet GL-MT6000";
+	compatible = "glinet,gl-mt6000", "mediatek,mt7986a";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs-append = " root=PARTLABEL=rootfs rootwait";
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1.8vd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_run: led@0 {
+			label = "blue:run";
+			gpios = <&pio 38 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led@1 {
+			label = "white:system";
+			gpios = <&pio 37 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	usb_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpios = <&pio 24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "2500base-x";
+		phy-handle = <&phy1>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy1: phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c45";
+			reg = <1>;
+			reset-assert-us = <100000>;
+			reset-deassert-us = <100000>;
+			reset-gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&pio>;
+			interrupts = <46 IRQ_TYPE_LEVEL_LOW>;
+			realtek,aldps-enable;
+		};
+
+		phy7: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c45";
+			reg = <7>;
+			reset-assert-us = <100000>;
+			reset-deassert-us = <100000>;
+			reset-gpios = <&pio 19 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&pio>;
+			interrupts = <47 IRQ_TYPE_LEVEL_LOW>;
+			realtek,aldps-enable;
+		};
+
+		switch: switch@31 {
+			compatible = "mediatek,mt7531";
+			reg = <31>;
+			reset-gpios = <&pio 18 GPIO_ACTIVE_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&pio>;
+			interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "lan4";
+					phy-handle = <&phy7>;
+					phy-mode = "2500base-x";
+				};
+
+				port@6 {
+					reg = <6>;
+					ethernet = <&gmac0>;
+					phy-mode = "2500base-x";
+
+					fixed-link {
+						speed = <2500>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+&pio {
+	wf_2g_5g_pins: wf_2g_5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			mediatek,pull-up-adv = <1>;	/* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			mediatek,pull-down-adv = <2>;	/* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			mediatek,pull-down-adv = <2>;	/* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			mediatek,pull-up-adv = <1>;	/* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			mediatek,pull-up-adv = <1>;	/* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			mediatek,pull-down-adv = <2>;	/* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			mediatek,pull-down-adv = <2>;	/* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			mediatek,pull-up-adv = <1>;	/* pull-up 10K */
+		};
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&usb_vbus>;
+	status = "okay";
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wf_2g_5g_pins>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};

target/linux/mediatek/filogic/base-files/etc/board.d/02_network

@@ -17,6 +17,9 @@ mediatek_setup_interfaces()
 	glinet,gl-mt3000)
 		ucidef_set_interfaces_lan_wan eth1 eth0
 		;;
+	glinet,gl-mt6000)
+		ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3 lan4" eth1
+		;;
 	h3c,magic-nx30-pro)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1
 		;;
@@ -63,6 +66,11 @@ mediatek_setup_macs()
 	bananapi,bpi-r3)
 		wan_mac=$(macaddr_add $(cat /sys/class/net/eth0/address) 1)
 		;;
+	glinet,gl-mt6000)
+		label_mac=$(mmc_get_mac_binary factory 0x0a)
+		wan_mac=$label_mac
+		lan_mac=$(macaddr_add "$label_mac" 2)
+		;;
 	h3c,magic-nx30-pro)
 		wan_mac=$(mtd_get_mac_ascii pdt_data_1 ethaddr)
 		lan_mac=$(macaddr_add "$wan_mac" 1)

target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata

@@ -15,6 +15,13 @@ case "$FIRMWARE" in
 		;;
 	esac
 	;;
+"mediatek/mt7986_eeprom_mt7976_dual.bin")
+	case "$board" in
+	glinet,gl-mt6000)
+		caldata_extract_mmc "factory" 0x0 0x1000
+		;;
+	esac
+	;;
 *)
 	exit 1
 	;;

target/linux/mediatek/image/filogic.mk

@@ -136,6 +136,20 @@ define Device/glinet_gl-mt3000
 endef
 TARGET_DEVICES += glinet_gl-mt3000
 
+define Device/glinet_gl-mt6000
+  DEVICE_VENDOR := GL.iNet
+  DEVICE_MODEL := GL-MT6000
+  DEVICE_DTS := mt7986a-glinet-gl-mt6000
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware e2fsprogs f2fsck mkf2fs
+  IMAGES := sysupgrade.bin
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-gl-metadata
+  ARTIFACTS := preloader.bin bl31-uboot.fip
+  ARTIFACT/preloader.bin	:= mt7986-bl2 emmc-ddr4
+  ARTIFACT/bl31-uboot.fip	:= mt7986-bl31-uboot glinet_gl-mt6000
+endef
+TARGET_DEVICES += glinet_gl-mt6000
+
 define Device/h3c_magic-nx30-pro
   DEVICE_VENDOR := H3C
   DEVICE_MODEL := Magic NX30 Pro