ipq60xx: add Qihoo 360v6 wireless support

target/linux/ipq60xx/base-files/etc/board.d/02_network

@@ -26,8 +26,26 @@ setup_network()
 	esac
 }
 
+setup_macs()
+{
+	case $(board_name) in
+	linksys,mr7350)
+		wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
+		lan_mac=$(macaddr_add "$wan_mac" 1)
+		;;
+	qihoo,v6)
+		lan_mac=$(mtd_get_mac_ascii factory lanMac)
+		wan_mac=$(macaddr_add "$lan_mac" 1)
+		;;
+	esac
+
+	[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
+	[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
+}
+
 board_config_update
 setup_network
+setup_macs
 board_config_flush
 
 exit 0

target/linux/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata

@@ -26,11 +26,31 @@ ath11k_generate_macs() {
 	echo -ne \\x${mac3//:/\\x} >> /lib/firmware/ath11k-macs
 }
 
+ath11kcal_die() {
+	echo "ath11cal: " "$*"
+	exit 1
+}
+
+ath11kcal_extract() {
+	local part=$1
+	local offset=$2
+	local count=$3
+	local mtd
+
+	mtd=$(find_mtd_chardev $part)
+	[ -n "$mtd" ] || \
+		ath11kcal_die "no mtd device found for partition $part"
+
+	dd if=$mtd of=/lib/firmware/$FIRMWARE iflag=skip_bytes bs=$count skip=$offset count=1 2>/dev/null || \
+		ath11kcal_die "failed to extract calibration data from $mtd"
+}
+
 case "$FIRMWARE" in
 "ath11k/IPQ6018/hw1.0/cal-ahb-c000000.wifi.bin")
 	case "$board" in
 	cmiot,ax18|\
-	linksys,mr|\
+	linksys,mr7350|\
+	qihoo,v6|\
 	zn,m2)
 		caldata_extract "0:art" 0x1000 0x10000
 		;;
@@ -48,6 +68,7 @@ ath11k-macs)
 	case "$board" in
 	cmiot,ax18|\
 	linksys,mr7350|\
+	qihoo,v6|\
 	zn,m2)
 		ath11k_generate_macs
 		;;

target/linux/ipq60xx/files/arch/arm64/boot/dts/qcom/ipq6018-v6.dts

@@ -15,16 +15,37 @@
 
 	aliases {
 		serial0 = &blsp1_uart3;
-// 		led-boot = &led_power;
-// 		led-failsafe = &led_power;
-// 		led-running = &led_power;
-// 		led-upgrade = &led_power;
+		led-boot = &led_system_orange;
+		led-failsafe = &led_system_red;
+		led-running = &led_system_green;
+		led-upgrade = &led_system_orange;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led_system_red: system-red {
+			label = "v6:red:status";
+			gpios = <&tlmm 71 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_system_orange: system-orange {
+			label = "v6:orange:status";
+			gpios = <&tlmm 72 GPIO_ACTIVE_HIGH>;
+		};
+
+		led_system_green: system-green {
+			label = "v6:green:status";
+			gpios = <&tlmm 73 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
 	keys {
 		compatible = "gpio-keys";
 
@@ -35,7 +56,7 @@
 		};
 
 		wps {
-			label = "reset";
+			label = "wps";
 			gpios = <&tlmm 19 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WPS_BUTTON>;
 		};
@@ -65,6 +86,16 @@
 			bias-pull-up;
 		};
 	};
+
+	leds_pins: leds_pins {
+		mux {
+			pins = "gpio71", "gpio72", "gpio73";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+	};
+
 };
 
 &soc {
@@ -205,4 +236,10 @@
 	status = "okay";
 };
 
+&qusb_phy_0 {
+	status = "ok";
+};
 
+&usb3 {
+	status = "ok";
+};