mediatek: add support for FZS P3

target/linux/mediatek/dts/mt7981b-fzs-5gcpe-p3.dts

@@ -0,0 +1,268 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "mt7981.dtsi"
+
+/ {
+	model = "FZS 5GCPE P3";
+	compatible = "fzs,5gcpe-p3", "mediatek,mt7981";
+
+	aliases {
+		serial0 = &uart0;
+		led-boot = &led_wifi;
+		led-upgrade = &led_wifi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0 0x40000000 0 0x10000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_wifi: wifi {
+			label = "green:wifi";
+			gpios = <&pio 15 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		4g {
+			label = "green:4g";
+			gpios = <&pio 34 GPIO_ACTIVE_LOW>;
+		};
+
+		5g {
+			label = "green:5g";
+			gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		nvmem-cells = <&macaddr_factory_2a>;
+		nvmem-cell-names = "mac-address";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+};
+
+&mdio_bus {
+	switch: switch@0 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_flash_pins>;
+	status = "okay";
+
+	spi_nand@0 {
+		compatible = "spi-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+
+		spi-max-frequency = <52000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+
+		mediatek,nmbm;
+		mediatek,bmt-max-ratio = <1>;
+		mediatek,bmt-max-reserved-blocks = <64>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "BL2";
+				reg = <0x000000 0x0100000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "u-boot-env";
+				reg = <0x100000 0x0080000>;
+			};
+
+			factory: partition@180000 {
+				label = "Factory";
+				reg = <0x180000 0x0200000>;
+				read-only;
+			};
+
+			partition@380000 {
+				label = "FIP";
+				reg = <0x380000 0x0200000>;
+				read-only;
+			};
+
+			partition@580000 {
+				label = "ubi";
+				reg = <0x580000 0x7000000>;
+			};
+		};
+	};
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@1 {
+			reg = <1>;
+			label = "lan1";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan2";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "wan";
+			nvmem-cells = <&macaddr_factory_24>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&pio {
+	spi0_flash_pins: spi0-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+
+		conf-pu {
+			pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+			drive-strength = <8>;
+			mediatek,pull-up-adv = <0>; /* bias-disable */
+		};
+
+		conf-pd {
+			pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+			drive-strength = <8>;
+			mediatek,pull-up-adv = <0>; /* bias-disable */
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		mux {
+			function = "uart";
+			groups = "uart1_1";
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		mux {
+			function = "uart";
+			groups = "uart2_1";
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+
+	mediatek,mtd-eeprom = <&factory 0x0>;
+};
+
+&factory {
+	compatible = "nvmem-cells";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	macaddr_factory_24: macaddr@24 {
+		reg = <0x24 0x6>;
+	};
+
+	macaddr_factory_2a: macaddr@2a {
+		reg = <0x2a 0x6>;
+	};
+};

target/linux/mediatek/filogic/base-files/etc/board.d/02_network

@@ -17,6 +17,7 @@ mediatek_setup_interfaces()
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan"
 		;;
 	cetron,ct3003*|\
+	fzs,5gcpe-p3|\
 	jcg,q30-pro|\
 	qihoo,360t7)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan

target/linux/mediatek/image/filogic.mk

@@ -146,6 +146,20 @@ define Device/cetron_ct3003-mod
 endef
 TARGET_DEVICES += cetron_ct3003-mod
 
+define Device/fzs_5gcpe-p3
+  DEVICE_VENDOR := FZS
+  DEVICE_MODEL := 5GCPE P3
+  DEVICE_DTS := mt7981b-fzs-5gcpe-p3
+  DEVICE_DTS_DIR := ../dts
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  KERNEL_IN_UBI := 1
+  DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-usb3
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += fzs_5gcpe-p3
+
 define Device/glinet_gl-mt2500
   DEVICE_VENDOR := GL.iNet
   DEVICE_MODEL := GL-MT2500
@@ -221,10 +235,6 @@ define Device/jdcloud_re-cs-05
   DEVICE_DTS := mt7986a-jdcloud-re-cs-05
   DEVICE_DTS_DIR := ../dts
   DEVICE_PACKAGES := e2fsprogs f2fsck mkf2fs kmod-mt7986-firmware mt7986-wo-firmware
-  UBINIZE_OPTS := -E 5
-  BLOCKSIZE := 128k
-  PAGESIZE := 2048
-  IMAGES := sysupgrade.bin
   IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
 endef
 TARGET_DEVICES += jdcloud_re-cs-05