mediatek: add support for netcore n60 pro

target/linux/mediatek/dts/mt7986a-netcore-n60-pro.dts

@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	model = "Netcore N60 PRO";
+	compatible = "netcore,n60-pro", "mediatek,mt7986a";
+
+	aliases {
+		serial0 = &uart0;
+		label-mac-device = &gmac0;
+		led-boot = &led_status_red;
+		led-failsafe = &led_status_red;
+		led-running = &led_status_blue;
+		led-upgrade = &led_status_blue;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0 0x40000000 0 0x20000000>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		mesh {
+			label = "mesh";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_red: status_red {
+			label = "red:status";
+			gpios = <&pio 29 GPIO_ACTIVE_LOW>;
+		};
+
+		led_status_blue: status_blue {
+			label = "blue:status";
+			gpios = <&pio 32 GPIO_ACTIVE_LOW>;
+		};
+	};
+	
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		nvmem-cells = <&macaddr_lan>;
+		nvmem-cell-names = "mac-address";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-handle = <&phy6>;
+		phy-mode = "2500base-x";
+
+		nvmem-cells = <&macaddr_wan>;
+		nvmem-cell-names = "mac-address";
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&mdio {
+	reset-delay-us = <600>;
+	reset-post-delay-us = <20000>;
+	reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+
+	phy5: phy@5 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <5>;
+		mxl,led-config = <0x0 0x0 0x0 0x3f0>;
+	};
+
+	phy6: phy@6 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <6>;
+		mxl,led-config = <0x0 0x0 0x0 0x3f0>;
+	};
+
+	switch: switch@0 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@1 {
+			reg = <0>;
+			label = "lan2";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan3";
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan4";
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "lan1";
+			phy-handle = <&phy5>;
+			phy-mode = "2500base-x";
+		};
+
+		port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+
+		spi-max-frequency = <20000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+
+		mediatek,nmbm;
+		mediatek,bmt-max-ratio = <1>;
+		mediatek,bmt-max-reserved-blocks = <64>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "BL2";
+				reg = <0x0000000 0x0100000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "u-boot-env";
+				reg = <0x0100000 0x0080000>;
+			};
+
+			factory: partition@180000 {
+				label = "Factory";
+				reg = <0x0180000 0x0200000>;
+				read-only;
+			};
+
+			partition@380000 {
+				label = "FIP";
+				reg = <0x0380000 0x0200000>;
+				read-only;
+			};
+
+			partition@580000 {
+				label = "ubi";
+				reg = <0x0580000 0x7280000>;
+			};
+		};
+	};
+};
+
+&pio {
+	spi_flash_pins: spi-flash-pins-33-to-38 {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+		conf-pu {
+			pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+			drive-strength = <8>;
+			mediatek,pull-up-adv = <0>; /* bias-disable */
+		};
+		conf-pd {
+			pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+			drive-strength = <8>;
+			mediatek,pull-down-adv = <0>; /* bias-disable */
+		};
+	};
+
+	wf_2g_5g_pins: wf_2g_5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wf_2g_5g_pins>;
+
+	mediatek,mtd-eeprom = <&factory 0x0>;
+};
+
+&factory {
+	compatible = "nvmem-cells";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	macaddr_lan: macaddr@1fef20 {
+		reg = <0x1fef20 0x6>;
+	};
+
+	macaddr_wan: macaddr@1fef26 {
+		reg = <0x1fef26 0x6>;
+	};
+};
+
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};

target/linux/mediatek/filogic/base-files/etc/board.d/02_network

@@ -19,6 +19,7 @@ mediatek_setup_interfaces()
 	asus,tuf-ax4200|\
 	jdcloud,re-cs-05|\
 	netcore,n60|\
+	netcore,n60-pro|\
 	ruijie,rg-x60-pro)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1
 		;;

target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac

@@ -67,7 +67,8 @@ case "$board" in
 		[ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress
 		;;
 	jcg,q30-pro|\
-	netcore,n60)
+	netcore,n60|\
+	netcore,n60-pro)
 		# Originally, phy1 is phy0 mac with LA bit set. However, this would conflict
 		# addresses on multiple VIFs with the other radio. Use label mac to set LA bit.
 		[ "$PHYNBR" = "1" ] && macaddr_setbit_la $(get_mac_label) > /sys${DEVPATH}/macaddress

target/linux/mediatek/image/filogic.mk

@@ -655,6 +655,20 @@ define Device/netcore_n60
 endef
 TARGET_DEVICES += netcore_n60
 
+define Device/netcore_n60-pro
+  DEVICE_VENDOR := Netcore
+  DEVICE_MODEL := N60 PRO
+  DEVICE_DTS := mt7986a-netcore-n60-pro
+  DEVICE_DTS_DIR := ../dts
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  KERNEL_IN_UBI := 1
+  DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += netcore_n60-pro
+
 define Device/nokia_ea0326gmp
   DEVICE_VENDOR := Nokia
   DEVICE_MODEL := EA0326GMP